Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Compressors 101?
-
15th August 2013, 03:44 AM #1Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Compressors 101?
I'm in need of a compressor.
I've been looking about and figure before I go out and get something that's unsuited to my needs, I should seek the collective wisdom of the forum.
So starting at the top.
New or Used?
Single or 3 Phase?.
Big or Small?
Single cylinder direct drive or multi cylinder belt drive?
I'd like something that could deliver enough for spraying polish varnish glue etc - maybe 20 cfm or thereabouts?
Also something not so noisy it will drive the neighbors nuts.
Something that won't break the bank in power costs.
So what I'm wondering is if a larger (or 3 phase even) compressor that obviously costs more - will have ongoing savings to run, if it's say 3 phase, starts up less often etc...due to a bigger receiver than a $50 direct drive single phase cheapie... that runs almost all the time and can't deliver enough air to be useful and drives the neighbors nuts with it's constant running?
I see a lot of larger compressors around the $600 - $650, against a lot of small Chinese direct drive 2.5 ho 40 ltr cheapies.
Are the cheap Chinese ones a false economy, more annoying, dearer to run in the longer term.
Just curious what the general consensus is - I've had a atlas copco in a previous life and a ingersol rand etc - but its been a few years, and things have changed a lot in the interim.
Mostly it might run a few nail guns...and some spray polishing...probably not large stuff. Typical cabby shop tasks.
I'll probably run some hard copper lines or HP Re9inforced hose or something, with drop lines & snap lock fittings above benches and machines.
Thanks in advance for anyone's done their homework & can pass on their knowledge.
Cheers
-
15th August 2013 03:44 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th August 2013, 03:53 AM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,813
Despite claims made to the contrary, 20 cfm is definitely 3 phase territory. The most a quality single phase can do is about 12 CFW with a tail wind and recent grease and oil change while cheaper units can only do 7-8 CFM.
My cheap chinese 2.5HP unit is now about 7 years old and refuses to die but I don't use for high volume air delivery - mainly I use it to get the swarf and lube off taps and dies. I did have to retighten the head bolts and refurbish the foil valves a couple of years back but it sounds like it is still good for another 7 years.
-
15th August 2013, 09:21 AM #3
G'Day Timless,
To get 20cfm you'll need at least a 5hp motor driving; it's 4cfm per hp as a rule of thumb....
5hp is a pretty big domestic motor and 3ph would be the way to go.
It maybe worthwhile looking at a petrol powered compressor with some good sound proofing & muffler??
Cheers, crowie
-
15th August 2013, 11:24 AM #4Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Bargain?
Air Compressor 3 Phase good condition
Cash and pick up only $50.00
This new Chinese single phase CLAIMS to be 19 cfm...
air commpressor19 CFM 240V 3HP motor 100L tank .hevy duty dubel belt ,
market value $900 am asking just $600 .
Brand new atlas copco compressor 3 hp ideal for small workshop or home workshop rrp $1299 can deliver I also have a 2 hp unit offering at $650 negotiable
Sooo - what am I missing here?
Should I be racing off to collect this $50 bargain before it gets away?
-
15th August 2013, 11:34 AM #5
My recommendations are as follows
- Belt Driven
- Twin or Triple heads pump
- Cast Iron Pump not Alloy
So going on those, I would ditch the $50 jobbie.
My 17cfm triple is still going strong after 20yrs or more with quite a few yrs of those being in an industrial situation.Cheers
DJ
ADMIN
-
15th August 2013, 11:45 AM #6
Timeless
It sounds as though you have some basic knowledge of air compressors from a previous life.
Big consumers of air are air driven tools and to a lesser extent paint spraying. A large 1PH compressor (3HP) will often have to be situated close to your power supply or the voltage drop will prohibit easy starting particularly from cold. If you have 3PH available I would go down that track and buy a second hand machine. Of course you would want to see it running to evaluate.
If your main use is a nailing gun, almost anything will do as they has a very low air consumption. Just a comment on the noise as it is my belief that the compressor makes the noise as opposed to the electric motor.
The important spec of any air compressor is the Free Air Delivery. It is the equivalent to HP at the rear axle on a car.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
15th August 2013, 12:14 PM #7Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Thanks fellas
Thanks Fellas - I'd honestly forgotten how much I like air powered tools in my previous life and how cheap they can be for the work they do..
The 2nd hand 3 phase one is just a 1 hp motor and something like 6-8cfm, according to its owner.
I might grab it today and see how it goes initially - if its no good (not enough air / too loud) - well for $50 I can always fill it with concrete and use it as a boat mooring!
What I saved on air, I can put towards proper dust extraction maybe or some more tools. Swings and roundabouts. It's all about the Journey - I keep telling myself this.
Cheers & beers fellas - its amazing how much one bloke can forget... the old saying if you don't use it, you lose it.
-
15th August 2013, 01:46 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,813
-
15th August 2013, 03:42 PM #9Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Yes indeed.
Yes Indeed Bob there seems to be fair degree of fudge factor in the gear coming out of China - but in fairness to the Chinese the guy building it, he might have had a dodgy bead on his abacus when he worked out the HP and CFM rates!.
-
15th August 2013, 04:05 PM #10
You need horsepower to get cubic feet per minute plus a big enough receiver to carry the volume for high air use...
******************************************************************************************************************
Rules of thumb:
- A good single-stage compressor, per true HP input, will deliver about 4 true CFM at 100 psig. It is not uncommon to see this more like 3 CFM per HP.
- A two-stage compressor is more efficient, typically by 15 percent, versus a single-stage compressor. You might see 4 to 5 CFM per HP at 100 psi, instead of 3 or 4 CFM.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Air compressors for the home or small shop have been advertised and sold with ridiculously inflated horsepower ratings. This was especially true before the year 2004, when the US government said it would enforce more honest ratings (see the end of this essay), and it seems to be returning to the marketplace after a year or two of spotty compliance. The specs and stickers on the unit likely do not tell the truth, and add confusion instead of critical information to buying decisions. But you do not need a testing laboratory to calculate true horsepower or CFM delivered. I will explain below how to estimate these ratings from pressure readings and elapsed time measurements.
The way to measure true power is to measure the time it takes to pump the reservoir tank of known volume from a known starting pressure to a known ending pressure. Then you can figure the true CFM from the difference in starting and final pressures, times the volume of the tank, divided by the time it took to pump up. You can also time the pump-up cycle from the cut-in to the cut-out pressure, since that's how one usually runs a compressor. These true performance measurements are impossible to fake.
The above is a quote from - Evaluating True Horsepower and CFM Ratings of Air Compressors
-
16th August 2013, 09:46 PM #11Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Well
Well the little old 3 phase $50 compressor now lives at my place!
I think it cost $50 in diesel to go get it!
The hose, tyre gauge/filler, water separator / regulator and blow down gun/nozzle are worth more than that!
I realize that its a bit large and heavy (cast iron) to be used anywhere but in the shed... so in due course I'll try and pick up a cheap $50- Chinese single phase one - and take it out onsite when I need to use an air nailer etc.
Can't hurt to have 2.
For now this old one will do for the shed!.
Might even treat it to a birthday and change the oil and clean the filter etc
It will probably break down in shock if I do!
See what tomorrow brings..... slowly slowly catchee monkey.
-
17th August 2013, 11:15 AM #12.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,813
-
17th August 2013, 12:39 PM #13Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
Ta Bob
Thanks for that Bob,
At this point I haven't even plugged it in yet, for all I know right at this moment - it might even run backwards.
I'll take a closer look this morning, it was all too hectic here last night.... to get anywhere near the shed UN-fortunately.
Edit:
This morning I ventured into the shed to play with the compressor...
Wouldn't you know it, it has a 10 amp 4 pin 3 phase plug while my outlet is 5 pin 32 amp outlet, so I can't even plug it in to test it!
I'll have to source another 32 amp plug end and swap them over!.
I also managed today to pick up a wet and al oxide dry wheel grinder off gumtree, for $75.
On the way home I swung by a garage sale, and picked up a brad air nailer and 2 x 25 meter extension leads for $100.
That's this fortnights play dough done and dusted...after the compressor, grinder, nailer and leads.
Slowly it's all coming together!.
-
19th August 2013, 09:09 PM #14Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
It goes!
Picked up a 32 amp 5 pin 3 phase male plug for the compressor today.
Now it works a treat, starts and runs fine etc... and after a few thread tape applications to various air blow down guns and tyre gauges as well as the air regulator inlet, it even holds air!.
I'm indeed a happy chappie with the progress made today!.
Not all days go this well.
Similar Threads
-
Air compressors
By K_S in forum GENERAL & SMALL MACHINERYReplies: 2Last Post: 22nd March 2010, 08:09 PM -
Compressors
By johna in forum HAND TOOLS - POWEREDReplies: 18Last Post: 26th November 2004, 04:31 PM -
gmc compressors
By mic-d in forum HAND TOOLS - POWEREDReplies: 1Last Post: 16th November 2004, 11:41 PM -
Compressors
By smidsy in forum HAND TOOLS - POWEREDReplies: 10Last Post: 23rd July 2004, 12:36 AM -
Compressors
By Mick4412 in forum HAND TOOLS - POWEREDReplies: 1Last Post: 20th July 2003, 09:52 PM