Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Jet 10-20 Drum Sander advice
-
20th July 2013, 06:03 PM #1
Jet 10-20 Drum Sander advice
Hi everyone,
I've just setup my new Jet 10-20 Drum sander and I'm pretty pleased with it on first look. I do have a couple of questions that more experienced hands might be able to help with:
1. Can I use regular abrasives in the machine? I'm a box maker so would like to be able to get a fine finish (say 300-400 grit) on the timbers before starting work. Just wondering if I could do this?
2. What the heck is the sheet of laminate for? In the box there is a nicely finished sheet of laminate about 15mm thick that doesn't seem to go anywhere. There is nothing about it in the manual and it seems weird that they'd just bung it in there to fill up space. It's not light at all!
Anyway, thanks in advance for your thoughts
Wok
-
20th July 2013 06:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th July 2013, 06:38 PM #2
Wok,
You can use standard abrasive papers. I get mine from The Sandpaper Man; one of the forum sponsors.
I buy mine in 10 metre rolls of 3" wide. It is preferable to buy the 3" as opposed to 75mm. Although this doesn't seem any different...3" is actually 75.72mm wide and if you use the 75mm, there is a small gap between each turn as you cover the entire drum.
Did you get an abrasive piece already on the drum...is so remove it from the drum and make a template of the strip out of a long piece of MDF or ply .....this can be used for cutting the rolls with the truncated ends then roll the abrasive back on the drum for use.
Can not help with the laminate other than maybe to place the machine on to give a solid base so the table doesn't warp.
Hope this helps
Skot
-
20th July 2013, 06:43 PM #3
Thanks heaps, Skot. The abrasive advice is what I really need. Brilliant, I shall get onto it tomorrow!
Cheers
-
20th July 2013, 07:23 PM #4
Wok...Just had another thought....
As I mentioned, remove the abrasive strip that comes with the machine (if it didn't have one try the internet for this info) ...now measure the overall length of the abrasive paper. I said in the previous post about buying 10m rolls BUT I have a 22/44 Drum sander and I buy my rolls in multiple of the abrasive length eg my strip may be 3.75m long so if I purchased 10m roll I end up with a lot of wastage.......2 strips and a piece 2.5 m leftover so I buy mine in multiples of 3.75m eg. 11.25m or 22.5m (23 metres) which means less useless pieces.
Hope that makes sense.
Skot
-
20th July 2013, 08:14 PM #5
I have the 16/32 and fine that anything above 120 grit tends to clog up pretty fast and finer grits tend to burn the timber.
My main choice is 80 grit then 120 for finishing. From then on it's festo or hand sanding..
I find I can put boards through twice in the same setting and still remove stock before lowering the head for further sanding.
Cheers
Steve
-
20th July 2013, 08:46 PM #6
I couldn't agree more Steve, I also only go to 120 then the Rotex for the fine finish. I also use the 2 pass trick. One thing I was advised by an "expert" at one of the wood shows was that a small gap between the paper helps clear the dust.
No idea what the piece of board is for wok, I must have missed that boat.
Cheers, Ian"The common law of business balance prohibits paying a little and getting a lot.. it can't be done.
If you deal with the lowest bidder it is well to add something for the risk you run.
And if you do that, you will have enough to pay for something better"
-
21st July 2013, 10:12 AM #7
Thanks heaps guys, I'll give the 120 a go and see how that travels. Work up in small increments, eh?
Today is a day for fiddling with sanders!
Wok
Similar Threads
-
Carba-Tec 635mm Wide Drum Sander - Single Drum
By macka75 in forum HAND TOOLS - POWEREDReplies: 6Last Post: 28th October 2021, 10:00 PM -
Help needed with Refurbing Cricket Bats- Advice on Drum Sander + Buffer needed
By Melbourne in forum WOODWORK - GENERALReplies: 23Last Post: 17th April 2014, 10:22 PM -
advice on buying drum sander
By dtpahs in forum WOODWORK - GENERALReplies: 27Last Post: 11th March 2012, 07:04 PM -
Balancing and truing Drum for Drum Sander
By Stetwood in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 27th May 2007, 11:12 PM -
Advice on drum sander / sharpener choice
By tonyhart in forum HAND TOOLS - POWEREDReplies: 8Last Post: 29th January 2005, 07:10 PM