Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
5th March 2014, 03:10 AM #1
Tablesaw motor stopped. Fix, or replace, and if so with what?
My 17 year old Taiwanese-made Carba-tec tablesaw stopped during a cut. It has a 2 hp motor. It did not bog down. It was a 2" thick cut into hardwood, which it has done many times before. No smoke (so I doubt anything has burned out). It just slowed and stopped. I pressed the reset button (no change), and there is power to the machine.
There could be a number of reasons, and the first thing I must do is check what the cause is. Can some kind soul here suggest a list of areas to check?
While my priority is to get the old girl running again, I am considering changing the motor for something more powerful if the cost is not too great. The current motor just does not feel like 2 hp to me, but it has been cutting 2-3" thick Jarrah for many years. However it has had a tendency to trip the reset/cutout switch when pushed a little. The saw is a decent one that I have much modified over the years, so worth hanging onto. I was thinking of a 3 hp or 4 hp motor. Which is the better deal (yes I know more power sounds better, but there may be penalties with this, such as increased power demands)? And where does one find a good, especially quiet induction motor in Australia? Any idea of the cost?
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
5th March 2014 03:10 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th March 2014, 09:38 AM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,808
Does it have one or two capacitors?
If it is has two capacitors, one will be the "start" capacitor and the other the "run" capacitor, if the later dies then that may cause the problem.
A long shot would be that the motor has developed an open circuit somewhere.
Shall I come around with some testing gear?
-
5th March 2014, 10:34 AM #3
Bob, that would be terrific. Any time over the weekend that suits you? We could check the dust levels again as well.
Best regards
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
5th March 2014, 04:49 PM #4Woodworker
- Join Date
- Apr 2006
- Location
- Brisbane
- Age
- 49
- Posts
- 395
Hi Derek:
I bought a 4HP 3Ph Hammer motor from Felder QLD a couple of years ago for about $400 from memory. It is a DOL motor, rated at S6 which is enough for my needs. I know there are cheaper options out there but I needed the more exxy alloy motor which is much lighter and much less bulky than the cast iron equivalents, so that it would fit inside my cabinet (1990 Delta Unisaw). I bought a magnetic switch at the same time. Yes, not cheap, but I hope to run my saw for a long while yet.
Hopefully, your issues will be minor and easily fixed! Cheers.Warm Regards, Luckyduck
-
6th March 2014, 06:10 PM #5SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Have you checked the overload located near the on/off switch
Had a friend that thought he had blown his motor,took it away to be repaired,put it back on ,still not running,found the overload ,rest it,all OK
$135 learning experience.
-
8th March 2014, 07:52 PM #6
Well Bob came around on Saturday morning. The first thing he commented on was the dust. Dust?! The sawdust in the tablesaw was nearly choking the blade! Well, I had planned to clean it out some time. It just sort of got away from me ...
So the tablesaw received it annual service and lube job. It helped. The motor was fine. The condenser was fine. The switches were fine. The problem was traced to dust on the connections!
All's well that ends well.
Thanks again Bob!
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
8th March 2014, 08:32 PM #7
Onya Bob! I take it there wasn't much point in checking the dust levels then?
-
8th March 2014, 08:37 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,808
Cheers Derek,
I forgot to say I have seen one slightly worse.
As I said you are lucky it did not catch fire - another reason for us all to get our dust collection sorted.
Bob
PS it was good to catch up and check out the never ending source of gizmos, ideas and fine furniture.
-
15th March 2014, 09:50 AM #9
Well done Bob.
Similar Threads
-
If only, I had stopped for lunch
By argeng in forum METALWORK FORUMReplies: 13Last Post: 16th April 2013, 12:05 AM -
Burnt out my motor- shall I replace it or buy a new lathe?
By Oiliver in forum WOODTURNING - GENERALReplies: 26Last Post: 21st September 2012, 12:43 AM -
Tablesaw motor short
By russell warke in forum TABLE SAWS & COMBINATIONSReplies: 4Last Post: 13th March 2012, 06:19 PM -
HELP The STUBBY STOPPED
By Calm in forum WOODTURNING - GENERALReplies: 32Last Post: 17th May 2009, 07:34 PM -
Tablesaw motor problem
By sundancewfs in forum TABLE SAWS & COMBINATIONSReplies: 14Last Post: 7th August 2008, 12:29 PM