Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Wiring a push buton switch
-
13th February 2012, 07:04 PM #1New Member
- Join Date
- Jan 2012
- Location
- Whangarei New Zealand
- Posts
- 5
Wiring a push buton switch
Hi,
On the 25th January I put up a post seeking a manual for a Morgan 150mm jointer. Well as luck and Google would have it I tracked down a manual for a similar American brand jointer (no doubt sourced from China). There was enough similarity to get the jointer assembled.
The only real worry I have is wiring. The manual was for an American machine and bears no resemblance to New Zealand 240V wiring. Earth is not a problem - that is very clear.
so my question is on a push button switch (off being the top button) and looking at the connectors at the rear rear of the switch which side is phase and which is neutral?
Any advice would really be appreciated.
Thank you.
Chris
-
13th February 2012 07:04 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th February 2012, 07:15 PM #2Novice
- Join Date
- Feb 2011
- Location
- australia
- Posts
- 16
Take a picture of the back (Terminals) and front of the switch, so we know what your talking about.
scott
-
14th February 2012, 04:45 AM #3Tool collector
- Join Date
- Nov 2004
- Location
- Santpoort-Zuid, Netherlands
- Age
- 67
- Posts
- 462
Hi Chris,
if the switch is of European make, the two input terminals onto which you fasten the two leads of the mains cord, are marked "P". The other two are the output terminals for the motor (other countries often use similar markings, or numbers). These switch type are often two pole setups (with two identical and mirrored switches), so it doesn't matter to which "P" you connect either the live or neutral wire. For the machine itself, however, it may matter which of its two terminals is connected to live or neutral. In that case, you must determine first, which P is connected to which output terminal when the "ON"-button is pushed. The output terminal that is connected to live when on, is the terminal onto which you fasten the machine's live lead. The other one is for neutral.
I could make you a drawing but a picture of your particular switch terminal layout is the best way to give a definite answer.
greetings
gerhard
-
14th February 2012, 12:09 PM #4
Gerhard, ... what's going on?
6 lines???
We enjoy your answers and we expect them to be LONG!
Cheers,
Paul McGee
-
14th February 2012, 06:37 PM #5New Member
- Join Date
- Jan 2012
- Location
- Whangarei New Zealand
- Posts
- 5
Further explanation - wiring a jointer switch
Hi,
Thanks for the advice.
As suggested by Scott I have uploaded a photo of the switch. A front view in the machine and two views of the connections. There are no letters or any indication of how this switch should be wired up. Any suggestions most gratefully received
Thanks again
Chris
-
14th February 2012, 08:37 PM #6Novice
- Join Date
- Feb 2011
- Location
- australia
- Posts
- 16
Pm sent.
I think if worked anyway let us know if u recive it
Scott
-
16th February 2012, 11:25 PM #7Tool collector
- Join Date
- Nov 2004
- Location
- Santpoort-Zuid, Netherlands
- Age
- 67
- Posts
- 462
Hahaha, hi Paul !
yours is a reaction i will always treasure! Brilliant! The first endorsement in writing that my long yarns are not necessarily bad. Thank you very much indeed!
best of greetings from Holland!
gerhard
-
17th February 2012, 02:11 AM #8Tool collector
- Join Date
- Nov 2004
- Location
- Santpoort-Zuid, Netherlands
- Age
- 67
- Posts
- 462
Hi Chris,
the switch in your pics looks like the double pole switch that i expected to be there. The wiring seems to be straightforward as well. Blue and brown in, blue and brown out. My guess is that, when the green "on" button is pushed, one set of switch contacts connects brown with brown and the other set blue with blue. This is the regular setup for a double pole switch. The absence of any markings means, that specific "in" and "out" connections are not important for this particular switch. Important is, that both mains wires must be mounted side by side, so either at the switch's upper side (the upper half of the assembly, with the red button) or at the lower side (down half, with the green button). The motor leads are also mounted side by side, but at the opposite half of the switch assembly. Do not connect one mains wire at the bottom and the other one at the top, because the mains voltage may be shortcircuited when the contact is closed. I made some drawings to explain the right setup.
Before you carry out the above, make sure that the switch indeed has the layout that is expect. Do can do so by measuring it. If you are uncertain in any way, have an electrician carry out the replacement of the switch.
gerhard
-
20th February 2012, 06:45 PM #9New Member
- Join Date
- Jan 2012
- Location
- Whangarei New Zealand
- Posts
- 5
Thanks for all the really helpful comments. The jointer is purring away. All I need to do now is make some fine adjustments . Thanks again to everyone.
Chris
Similar Threads
-
push knife
By wheeloftime in forum WOODCARVING AND SCULPTUREReplies: 17Last Post: 5th January 2010, 11:11 PM -
Wiring up Start Switch to motor, 8" JET Jointer
By Friday in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 2Last Post: 20th September 2007, 08:22 PM -
safety switch wiring!!
By SAFFA in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 3Last Post: 17th July 2006, 11:19 PM -
Could you give me a push please?
By Bob Willson in forum WOODIES JOKESReplies: 0Last Post: 14th October 2004, 03:09 PM