Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 76 to 90 of 107
Thread: Advice
-
15th December 2007, 07:56 PM #76
Hi garfield
2.5 Dia should be OK.
If you cut it square and dress it so it butts up with no gap you should be fine.
The diagram below I did for some one else on the forum, but it will work just as well for you. Tack all the corners first OK!
Try to keep 2/3rds of your arc on the uncut side. keep the amps on the low side and the arc short.
We all all waiting to hear of the results with bated breath.
Grahame
-
15th December 2007 07:56 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th December 2007, 11:03 PM #77
Ok thanks Grahame. Mate i'll be sure to post some pics when it's all done.....
-
19th December 2007, 08:09 AM #78
Does anyone know of any other metal places in the Blacktown - Minchinbury areas please? I tried Edcon for some 22mm steel pipe with a 2mm wall and a 19mm steel pipe 2mm wall to fit inside but they can't help. So I'm wondering if i'll have some luck smoewhere else.
Thanks guys
-
19th December 2007, 09:57 AM #79
The best place for steel around our area is Sims at Dunheaved. They sell at wholesale rates to public. The only catch is that they are OH&S Natsies, and you have to bear that in mind when loading etc.
-
19th December 2007, 10:46 AM #80
Thanks for that. I also found another place too.... their called Orrcon at glendenning, they seem quite good on their prices too.
-
19th December 2007, 12:23 PM #81GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Garfield you wont find anywhere that will have 22mmOD 2mm WT that 19mmOD will fit into ,you need to be smaller than 18mmOD.
Your only option if these are the sizes you require is to turn the OD of the 19mm to suit the ID of the 22mm.
-
19th December 2007, 01:29 PM #82
Mabey it is available.
I have purchased similar sizes before for a table saw trunnion that I built a few years back.. It will cost you a packet though. $$$$
There is a place near Blacktown that will have it. You will need to ask for internally ground bore tube. I can't remember the name of the shop, but here are some directions.
Going nominally west down Sunnyholt towards Parkleah from Blacktown, you turn left at the + intersection before heading up the hill. Continue down about 1km and turn right at the servo. The steel place is 50m up there on the RH corner.
-
19th December 2007, 02:28 PM #83GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Just curious fossil if you can get the sizes of tube that Garfield requires im amazed that they slip inside each other without the aid of a 250 plus tonne power press.
-
19th December 2007, 02:29 PM #84
Garfield,
Does this help in seeking dimensions for for
Pipe nominal bore
Tube OD Outside dimension
http://www.austubemills.com/document...PAGMay2007.pdf
Grahame
-
19th December 2007, 05:01 PM #85Just curious fossil if you can get the sizes of tube that Garfield requires im amazed that they slip inside each other without the aid of a 250 plus tonne power press.
You are 100% correct, in that any telescoping sizes in NB pipe will not fit, hence my suggestion to the O.P. to consider internally ground tube.
-
20th December 2007, 12:08 PM #86
I just looked it up on whereis and the place I was refering to is on the corner of Turbo and Binney rd's at Kings park, between Blacktown and Marryong.
Good luck.
-
21st December 2007, 09:27 PM #87
sorry for the no reply, but my computer sh@t itself and I couldn't view for a couple of days.
Thanks guys....
-
22nd December 2007, 11:13 PM #88
-
23rd December 2007, 02:52 AM #89GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
Garfield you can try ERW tube you can get it in 22.2mmOD x 1.2 or 1.4 mmW/T,this will accomadate 19mm ERW tube.
Only problem is your W/T (the welding concern)
How far does the 19mmOD tube or pipe have to slide in side the larger diameter.
As said before may be easier to get some 19mmOD pipe and turn the OD of this (you can get 19mmOd in 3.2 W/T so taking a bit off the OD would not effect its rigidity.
Depending how long it may need to be turned could probably assist you with that.
-
23rd December 2007, 08:27 AM #90
Similar Threads
-
Picture framing equipment advice please.
By AlexM in forum WOODWORK - GENERALReplies: 32Last Post: 24th July 2008, 01:11 AM -
1928 Sydney Harbor Ferry
By myrnaboys in forum BOAT BUILDING / REPAIRINGReplies: 84Last Post: 7th May 2008, 11:29 PM -
advice for newbie on sanding bondwood yacht
By Ezra2 in forum BOAT BUILDING / REPAIRINGReplies: 3Last Post: 23rd April 2006, 10:37 AM -
New Workshop Advice
By dazzler in forum WOODWORK - GENERALReplies: 18Last Post: 4th January 2005, 10:44 AM