Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Failing Vision
-
2nd October 2013, 01:46 PM #1Novice
- Join Date
- May 2013
- Location
- Adelaide Hills
- Age
- 59
- Posts
- 16
Failing Vision
Hi All, been going over some old posts regarding helmets, lenses, eyesight etc. I use a Speedglas utility and, over time have also noticed the eyes are not what they used to be! Well I ran out of the clear polycarb outer covers but needed to do a couple of repairs on the trailer. My problem was that once the arc started (using a Lincoln Powermig 180c, and I LOVE it!) I lost sight of the welding line and was pretty much guessing. Didn't want to drive an hour to get more, mainly because I seem to have refined the art of laziness. Anyhow I took the best of the worst covers and spent 10 minutes polishing it with a soft cloth and some good old toothpaste. The difference was incredible and although the covers really didn't SEEM all that bad, I can only assume the arc plays havoc on even the slightest imperfections on the cover. Just thought I would pass it on and if it helps anyone else out there, all the better............Cheers
-
2nd October 2013 01:46 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd October 2013, 03:07 PM #2Member
- Join Date
- Jun 2012
- Location
- melbourne
- Posts
- 59
I had heard of using toothpaste as a fine polish 30 years ago, and I tried it on a motorcycle visor back then, but I would have been better using a brilo pad. It scored the plastic badly and ruined the visor. I'm guessing there are different grades of toothpaste, so just be sure to test in an area that's not important if you want to give it a go.
-
9th October 2013, 11:23 PM #3danielson
- Join Date
- Dec 2009
- Location
- broadford
- Age
- 63
- Posts
- 237
brasso and silvo also do a brilliant()job.while we are on the subject,i have fitted a boc magnifying lense under my polycarb cover to aid my failing vision.only $15 or so bucks,worth a look.
-
10th October 2013, 08:32 AM #4Member
- Join Date
- Jun 2012
- Location
- melbourne
- Posts
- 59
I use brasso and silvo to polish plastic too, they are pretty good. I only once ever had a problem where the plastic crazed because of the solvent. To get things really optically clear though is hard as even the metal polish leaves fine scratches if you shine a light across it. I got a plastic polish out of a yacht chandler that works as well as anything I have found, and would be my first choice now.
Regarding the lenses you can fit in the welding helmet, I tried one and it was OK. I was one of those guys who didn't realise how poorly I could see the puddle, because old age sneaks up on you. My welding immediately improved 100's after getting the lens. My eyesight is failing through old age as it does, and I can still focus down to arms length well, but after that things get fuzzy. I'm sure thats a common symptom to anyone over 45 and it just gets worse! What I found was better than the fixed lens in the hood, was a range of those reading glasses for a few $ each. I do some fine welding where I need to get really close (5~10amps) and I need a #3 for that (focusing at less that 12") and various other numbers to cover the full range up to 3 ft. The glasses seem to only cover a very narrow range of focus, which gets narrower, the more they magnify. For normal welding a 1.5 is good for me. I preferred the fact you can change them so easily, over the fixed lens in the welding helmet.
-
14th October 2013, 07:13 AM #5Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Agree with the cheap reading glasses. I find them sharper than the cheater lens I tried.
Michael
-
14th October 2013, 10:09 PM #6
I will try reading glasses tomorrow. They may help me as well. My vision is ok down to about 30 cm away so I may be a bit too far away most of the time for the benefit. I will also look into cleaning the lens covers on the helmet although I bought quite a few from EvilBay recently. One of the ones I have in at the moment I made up from a piece of face mask plastic which got broken, not thru impact during use. It split down the middle, top to bottom.
Dean
-
15th October 2013, 01:26 AM #7GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,695
I have stopped welding due to poor vision or more accurately the inability to see the weld line. I have perfect vision (no glasses to read or see at all) but the eye does not transmit the light when you are sixty plus even if you don't need glasses. i think the figure is something like a 25 year old needs four times less light to see the same thing. I tried a new speed glass helmet the other day and while it assisted in making it easier to start in the right spot actually getting the weld metal where it was supposed to go was a bit hit and miss. No glasses at my age? don't ask it cost a bloody fortune, implanted lenses during cataract surgery.
CHRIS
Similar Threads
-
A question regarding failing vision
By Grandad-5 in forum WELDINGReplies: 30Last Post: 29th July 2011, 12:57 AM -
Failing CA
By brendan stemp in forum WOODTURNING - GENERALReplies: 21Last Post: 6th July 2011, 01:56 PM -
Cabinet Vision
By Toolin Around in forum DESIGN & DESIGNING / GOOGLE SKETCHUPReplies: 2Last Post: 20th June 2008, 10:51 PM -
Flashes in peripheral vision in one eye?
By Cliff Rogers in forum HEALTH ISSUESReplies: 21Last Post: 18th October 2007, 06:13 PM -
Eye Sight Failing...Getting Old
By stevew in forum METALWORK FORUMReplies: 7Last Post: 10th December 2006, 09:32 PM