Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 46 to 54 of 54
-
26th April 2012, 08:56 PM #46Retired
- Join Date
- Aug 2008
- Location
- Liverpool, NSW
- Posts
- 55
I had a 130 amp MIG with a 10 amp plug and it was pretty useless. Not necessarily due to low capacity but because of an awful wirefeed. Got rid of it luckily enough and bought a decent unit instead.
It taught me to 'buy bigger and better than I think I will ever need' and it will be just right as my capabilities grow.
-
26th April 2012 08:56 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th April 2012, 10:36 AM #47GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
Apples and oranges here.
Agreed, a 130A mig is a somewhat limited tool, particularly as most are fitted with poor wire feeds and short gun leads, however a stick welder, particularly an inverter, with a genuine 130A is a very good tool, capable of performing in an industrial application let alone a home environvent.
We seem to be hung up on the 10/15A debate somewhat in this thread. If a reputable machine comes with a 10A plug, then it is suited for usage on a circuit rated at that level, likewise for a 15A.
Some people will make the call that they can file plugs, make adapters and the like. That is their call and no one can/will tell them that it is ok officially. Just as someone may choose to plug two double adapters into a double 10A power outlet and load it up to 40A. This situation is compunded when heavy loads are run on long extension leads.
-
27th April 2012, 12:49 PM #48Senior Member
- Join Date
- Feb 2011
- Location
- Mornington Peninsula
- Posts
- 183
-
27th April 2012, 04:07 PM #49Rocket (Rod)
- Join Date
- Nov 2011
- Location
- Mickleham
- Posts
- 84
And with a fairly good stick welder, is there even a need for a backyarder to need a MIG as well or instead of a stick welder?
Some people will make the call that they can file plugs, make adapters and the like. That is their call and no one can/will tell them that it is ok officially.
Some hazards are obviously risky, like walking on a rope across the Grand Canyon. So you wouldn't need a law to make such illegal, because the danger is obvious. However, with electricity, the dangers are not obvious, as has been proved in this thread. So because of the lack of obvious dangers, there are laws that prohibit anyone from modifying/tampering with wiring etc.
Which is why there wouldn't be as many GPO's hanging off the kitchen circuit as there would be on other circuits. Basically, each GPO gets nominated points, depending on its location and likely use, and that determines how many get hooked up to each breaker.
Cheers
-
27th April 2012, 04:20 PM #50
-
27th April 2012, 04:28 PM #51Senior Member
- Join Date
- Feb 2011
- Location
- Mornington Peninsula
- Posts
- 183
Agreed.
I think you will find that the MIG is the great all-rounder welder especially when you consider that it does not take long to get the hang of it and produce good quality work.
ARC has its place but for general home use with predominately mild steel I don't think you can beat a MIG.
My old MIG I paid $600 odd back in the early 90's and it lasted me 20 years and paid for itself 100's of times over. Only half a dozen times I wished I had an ARC welder instead.
Cheers
Justin
-
27th April 2012, 04:30 PM #52Senior Member
- Join Date
- Feb 2011
- Location
- Mornington Peninsula
- Posts
- 183
-
27th April 2012, 04:45 PM #53Rocket (Rod)
- Join Date
- Nov 2011
- Location
- Mickleham
- Posts
- 84
Whenever I've needed to weld something so far, I've either dragged the gas axe out, or gone to the neighbour.
My most recent gas axe task was butt joining 1.6 mm wall thickness 50 mm RHS. While a mig could have done that easily, I'm not sure if a stick welder could have, with my ability anyway.
Of course a mig or stick welder is tied to the shed, but for the projects that I am likely to do in the next few years, that isn't an issue.
Thanks for the replys guys.
Cheers
-
28th April 2012, 09:31 AM #54
If your doing occasional home use stuff i.e 10 cm runs in up to 6mm then a cheap
$200 140amp should be fine as I find i rarely use more than 2 rods before stopping and cleaning and setting up the next run. I have yet to find the occasion or need to run it to the duty cycle limit. I have repaired trailers and made mobile machinery bases etc and have never had an issue. But given that if I tried to weld a I beam then I would have an issue
A Gas shielded mig would be nice but for the amount of times i use it the cheap arc is more economical. As the mig cost and the bottle rentals are a killer for mig
Andrew"All that is necessary for evil to succeed is for good men to do nothing"
(Edmund Burke 1729-1797)
Similar Threads
-
Anyone Welding ally with a dc stick welder ?
By Mathuranatha in forum WELDINGReplies: 1Last Post: 7th January 2010, 07:19 PM -
Inverter Arc / Stick welder recommendations
By Matty5700 in forum WELDINGReplies: 10Last Post: 17th May 2009, 10:53 AM -
I want to buy a Stick Welder
By 8679 in forum WELDINGReplies: 22Last Post: 2nd May 2009, 11:38 PM -
alluminium rods for stick welder??
By Gedmet in forum WELDINGReplies: 5Last Post: 15th March 2009, 05:16 PM