Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: new welder
-
24th July 2011, 10:29 PM #1son of a blacksmith
- Join Date
- Jun 2011
- Location
- Roxby Downs Sth Aust
- Age
- 47
- Posts
- 254
new welder
thinking about buying a new welder, anyone got any knowlede on the one in the link? performance/ reliability?http://www.gasweld.com.au/products/580006
its a coppermate 250 amp welder (incase the link doesnt work)
-
24th July 2011 10:29 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
25th July 2011, 10:18 AM #2GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
Seems ok, dual voltage so you can run low hydrogen, (use the high setting more most things), duty cycle will be fine for general use.
One question, how good is your power supply? If you are running this off 240v then it will eat power at it's higher settings, (I dispute their 20A powerpoint claim as I have done this with a similar welder). Perhaps, if you have not already, consider an inverter power source. They are not the be all and end all, but are another option.
-
25th July 2011, 07:41 PM #3son of a blacksmith
- Join Date
- Jun 2011
- Location
- Roxby Downs Sth Aust
- Age
- 47
- Posts
- 254
i just want the option of been able to burn 4mm rods and not tripping the power after 30 seconds, as for power supply, im sure the 20 ampre plug wil be fine, just need to change the 15 breaker and gpo to 20s. spoke with my neighbour who's a sparky and he says its not a problem.
the main thing is: not wanting to make the buy purely based on the 250A and thats its red, need to know if anyone out there has used one, knows of anyone who has one and how reliable it is. will it become a door stop after a days welding? if so i can use my old welder for that already.
thanks.
-
31st July 2011, 09:49 AM #4GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
End of the day, not much can go wrong with this type of welder. Other than the windings overheating and failing there are few areas for failure and it does have a 10 year warranty. A big plus is the use of copper windings.
Not to labour the point, but I do not believe that you will run that welder off a 20A circuit breaker at anything near maximum current for very long. I have a 220A Peerless and running it off 20A fuse wire I found I would have to replace the fuse wire monthly as it had been carrying so mujch current that it had heated up and oxidised. Welders produce surge current loads far in excess of their rated current draw and my experience with circuit breakers has been that they do not handle these as well as fuse wire of the same amperage.
My guess is that you will not be welding at 250A very much anyway, although if you were to run 4mm electrodes at 170A on the high voltage setting, you would be getting up there as far as current draw goes.
Similar Threads
-
DIY TIG Welder
By Edd in forum WELDINGReplies: 23Last Post: 2nd March 2010, 10:22 AM -
Which welder?
By mac_man_luke in forum WELDINGReplies: 28Last Post: 20th December 2009, 07:46 AM -
What do you think of this welder?
By jackaroo in forum METALWORK FORUMReplies: 9Last Post: 7th July 2007, 01:48 AM -
MIG Welder DOA :(
By Dean in forum WELDINGReplies: 12Last Post: 4th June 2007, 10:29 PM