Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 20
Thread: The Sharpening Machine
-
14th August 2013, 08:16 PM #1
The Sharpening Machine
The sharpening machine I have for my thicknesser and jointer is a little beauty in my highly biased opinion.
I did make some reference on the jointer thread so here it is. German made and dating from the mid 50s, it is a bench grinder that is traversed over the blades, which in turn are clamped to a bed. Completely manual with an adjusting screw to very gradually lower the wheel onto the blade.
The angle of the bed can be adjusted and I usually have set firly steeply to suit most of the dense hardwoods I plane.
The funny things is that until today, if you asked me the size of the motor I would have said 1/4HP but as you can plainly see from the spec plate it is 1 1/4HP (1KW).
It works extremely well and I sharpen all my electric plane blades on it as well as chipper blades for the mulcher.
Sharpening machine 005.jpgSharpening machine 004.jpgSharpening machine 001.jpgSharpening machine 002.jpgSharpening machine 003.jpg
Really the grinding wheel should have a guard. There is also a rest use for grinding primary bevels on chisels, but I have never used that.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
14th August 2013 08:16 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th August 2013, 09:01 PM #2SENIOR MEMBER
- Join Date
- Nov 2011
- Location
- Newcastle NSW
- Posts
- 775
Paul,
A dangerous move, listing this. The first thing I did was check your location. Nice compact design.
cheers,
Camo
-
14th August 2013, 09:28 PM #3
-
15th August 2013, 10:32 AM #4SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 856
Nice unit, I wonder if anyone makes a similar unit these days. You could probably use it of sharpening handplane blades as well I suppose.
joez
-
15th August 2013, 11:33 AM #5
Joez
I have seen sharpeners, but the blade seems to be the component moved, not the grinding device. I have not seen my style of sharpener anywhere else so I thought it might be of interest.
You could sharpen almost anything that can be clamped I suppose.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
18th August 2013, 12:35 AM #6China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
Most pro sharpening shops use this design except the wheel is run flat ( cup wheel) so it gives flat grind, very commonly Italian made,
some of the more expensive units are from Sweden
-
18th August 2013, 08:35 AM #7
...now isn't that the duck's guts.
Haven't seen one of those ever. You'll have to video it in action Paul.
-
18th August 2013, 06:12 PM #8
-
14th September 2013, 07:12 AM #9
It may work even better if you replace that Green wheel with a softer white one.The green is usually for Tungsten Carbide.
Cheers from Micheal.
-
14th September 2013, 09:08 AM #10
Michael
Now that is interesting. How that wheel came about was that a mutual friend of ours rehabed the machine before it was set up and he replaced the wheel. The original was just the standard grey wheel. I know he put that on there because of the 18% tungsten that is commonly present in planner blades.
However, from your comments the wheel is intended for pure tungsten and he was mistaken in his choice of wheel. I will have to look into that.
Thank you
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
14th September 2013, 09:42 AM #11Retro Phrenologist
- Join Date
- Oct 2009
- Location
- Springfield NSW
- Age
- 70
- Posts
- 1,007
Hmmm
I was going to say "I'll be there shortly", but I am just a bit too far away.____________________________________________________________
there are only 10 types of people in the world. Those that understand binary arithmetic and those that don't.
-
14th September 2013, 09:51 AM #12
Hey Scotty, how long before you get that transporter ready....
The person who never made a mistake never made anything
Cheers
Ray
-
14th September 2013, 11:45 AM #13
Stay with a reasonably coarse wheel 46grit and you may find it grinds bit cooler.
The machine also looks to be at odds with itself.If that is a grinding rest for chisels near the wheel the stone would be spinning the wrong direction.It should be spinning towards the blade in the main holder which would be away from the manual rest.Does it have a reversing switch by any chance?Cheers from Micheal.
-
14th September 2013, 11:54 AM #14.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
That's a sweet looking unit Paul.
The name plate says it's 3 Phase so it should be easy to engineer a reverse on it.
Better still (seeing it is a 220/380V motor) would be to use a small VFD and then you would have speed control as well.
Cheers
Bob
-
14th September 2013, 03:34 PM #15
Michael
You had me going there for a moment . As I said, I have never sharpened chisels with this machine. The grinder spins clockwise so the direction is correct for a chisel or handplane blade. For the long blades that are clamped the grinder starts on the heel of the bevel and progresses towards the sharp end.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
Similar Threads
-
United states machine tool co. #1 horizontal milling machine
By pmcgee in forum ANTIQUE AND COLLECTABLE TOOLSReplies: 0Last Post: 1st March 2013, 11:16 PM -
Tormek sharpening machine
By Dez Built in forum WOODTURNING - GENERALReplies: 101Last Post: 26th January 2012, 10:26 PM -
blade sharpening machine ?
By charlsie in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 20Last Post: 21st January 2010, 09:56 PM -
clamps- Chisel Sharpening Machine
By clamps in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 0Last Post: 2nd May 2009, 08:05 PM -
Saw Sharpening Machine
By bendigo P/T in forum ANNOUNCEMENTSReplies: 4Last Post: 13th September 2007, 03:04 PM