Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Hermle clock movements
-
4th September 2012, 07:41 PM #1
Hermle clock movements
I am about to build a George III bracket clock (it is on the list any way) it will have a Hermle 340-020 movement any one know where I can get information, I want to:
- Be able to silence it at night, is there a lever that I can fit (Mrs Phil reckons the Westminster chime will keep her awake at night)
- How to time the movement It has a spring escarpment
- When I unpack it do I have to oil it and at what points
- Any one know where I can get a data sheet on the movement
Any info will be gratefully received.
When I start construction I will post pictures.Two things are infinite: the universe and human stupidity; and I´m not so sure about the universe.
-
4th September 2012 07:41 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
5th September 2012, 12:00 PM #2Novice
- Join Date
- Jun 2012
- Location
- Northumberland - UK
- Posts
- 17
Hi,
You may be interested in the following book Clock Repair Tips for Hermle 340-020 Movement by Bill C. Tipton website BK-205 price $29.95.
this will answer all your questions. Reards Eastgate
-
5th September 2012, 01:12 PM #3
-
8th September 2012, 08:39 PM #4Member
- Join Date
- Jan 2009
- Location
- Melbourne
- Posts
- 56
Hi Phil,
Apologies for finding this late. I think that I can help you. I have used this movement in two clocks. One is the mantle clock shown in the second photo in a post I made in this section in July 2009. The other was made 13 years ago. I have made a number of clocks and, these smaller two have the only non pendulum movement I have ever used. I have to admit that they are reliable and can be made to maintain quite accurate time but, without a pendulum have some limitations in time adjustment.
The movement does have a silencing lever. I adapted this to a lever on the rear of one clock to avoid opening the back every time.
The spring escapement has a screw adjuster to time it. Turn clockwise to make slower and anticlockwise to quicken. 60 degrees is approximately 10 seconds per day. One complete turn is approximately one minute per day.
I would oil the movement, simply because you do not know when it was made and oiled.
PeterLast edited by Pete L; 9th September 2012 at 02:55 PM. Reason: clarification
-
9th September 2012, 08:29 AM #5
-
12th October 2012, 08:11 AM #6Senior Member
- Join Date
- Mar 2007
- Location
- Picton, NSW
- Posts
- 143
When oiling the clock
1. Only use special clock oil, NOT light machine oil, etc NOT NOT NOT WD40 or the like. Clock oil is formulated to stay in place and not to run away from where it is placed. You can pick it up on eBay! (eg CLOCK OILER | eBay )
2. Only oil the "oil sinks", that is the small indents where the gear axles (pivots) protrude through the plates. Just a half a drop on the end of a 0.5mm wire, or pin is enough. It will "capillary" down between the pivot and the brass plate and stay there.
3. DON'T oil the actual gears themselves! They are designed to "roll" together rather than "slide" together, so there is very little friction between the cogs. Oil there just attracts dust and causes abrasion, rather than preventing it!
4. DON'T bother oiling lever pivot points, etc. Again, just not necessary.
I hope this helps.
cheers
Walesey
Similar Threads
-
Hermle clock movements
By Whit68 in forum CLOCKSReplies: 4Last Post: 31st July 2011, 10:53 PM -
Clock movements
By tweak in forum CLOCKSReplies: 11Last Post: 27th October 2010, 10:48 AM -
Clock movements
By tazchris in forum WOODWORK - GENERALReplies: 1Last Post: 29th July 2006, 10:19 PM -
Clock Movements
By Shane Watson in forum WOODWORK - GENERALReplies: 6Last Post: 2nd January 2001, 10:13 PM