Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 15
Thread: GIS lumber
-
7th February 2013, 08:22 AM #1New Member
- Join Date
- Jan 2013
- Location
- Thomasville GA
- Posts
- 5
GIS lumber
After sending my materials list to a half dozen places, I finally got a quote on the lumber I need. They want $900 for the WRC, Douglas fir, and white oak. This does NOT include the plywood, which I ordered from somewhere else. Does this sound reasonable to any of you who may have built the GIS? Since I have only been able to get one estimate, I don't have anything to compare it to.
-
7th February 2013 08:22 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th February 2013, 03:19 AM #2
Does that include cutting and milling to exact dimensions? That's a lot of money in my mind. I'm pretty sure I didn't spend more than $300 at Home Depot and a local yard that had a nice price on a load of Eastern White Pine (my substitute for WRC). True, Doug Fir is plentiful here. But still...
If it DOES include labor, that makes it tougher to comment on. Now you're talking about the value of your time, the price of local labor, your willingness to provide economic stimulus in your community, the price of tea in China, etc.Dave
StorerBoat Builder, Sailor, Enthusiast
Dave's GIS Chronicles | Dave's Lugs'l Chronicles | Dave's StorerBoat Forum Thread
-
8th February 2013, 11:56 AM #3
Re: GIS lumber
Maybe a little high. I just got quoted ~$300 for Paulownia with another $100 for delivery (5500km) dressed to size, still cheaper than wrc. Yellow cedar my Oregon substitute cost me $150 but needed ripping and dressing. Hardwood I've acquired for free. Plywood is $105 per sheet. I hope this helps.
Dan
Sent from my GT-I9305 using Tapatalk 2
-
10th February 2013, 02:32 AM #4SENIOR MEMBER
- Join Date
- Sep 2007
- Location
- Savannah GA USA
- Posts
- 583
Way too high. Just pick through the two-by stuff at Home Depot/Lowes. I used their standard lumber carefully selected and cut to avoid the knots. I couldn't find any hardwood suitable for the outer rub rail so I switched to SYP for that.
I settled for a width of 1 1/2 inches for the framing, ignoring the metric dimensions called out in the plan which was about 1 3/4 IIRC. To make up for the smaller width I cut the framing a little thicker than called for. Doing that gave me pretty good utilization of the standard two-by lumber available in the US.The "Cosmos Mariner,"My Goat Island Skiff
http://s176.photobucket.com/albums/w168/MiddleAgesMan/
Starting the Simmons Sea Skiff 18
http://www.flickr.com/photos/37973275@N03/
-
10th February 2013, 09:42 PM #5
My quote from a couple of months back,
Oregon $407
WRC $407
skids and cappings, hardwood (victorian ash) $132
So $956 all dressed in lengths required as per material list. I think that's for everything you got quotes for Tippy. So that doesn't include mast timber or ply.
FWIW, hoop pine ply quote for the 6 sheets was $924 @ $154 each. Gaboon equivalent is around $100 a sheet.
Not in a position to build yet so I haven't moved on the quote but may look at substitutes when I'm ready, I just don't know.
-
19th February 2013, 01:33 AM #6Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
Dimensions
I'm also having trouble with the dimensions of finished lumber being so far off the quoted size that I can't make it match what is called for in the GIS plans. For instance, one inch WRC is actually 3/4 (19 mm) which makes it far short of the 22 mm called for. How important is that.
I too am looking into quotes so am glad to see this thread.
-
19th February 2013, 05:46 AM #7Senior Member
- Join Date
- Sep 2011
- Location
- Gothenburg, Sweden
- Posts
- 100
GIS lumber
19mm thick wrc is what's called for in my plans... 19x45, 19x19.. If you are off more than a mm in thickness you have to take that into account when you are bevelling the bulkheads etc. Structurally it won't be any problems (within reason)
Pontus
-
19th February 2013, 10:04 PM #8Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
Lumber dimensions
I don't think I made my self clear enough. What worries me are the mast, spars and dagger board dimensions since these three have by the most stress in the boat. It effects the dimensions of the dagger board case as well. 19 mm would be 3 mm short on the dagger board and that seems light to me on something that carries that amout of stress.
-
19th February 2013, 11:51 PM #9
For the dagger board, pretty important IMHO. The template for the foil shape is based on 22mm. The spacer dimensions of the centercase are too (less important). However, it just popped into my head that there are also foil templates for 18mm blades for those who chose to make them from three layers of 6mm ply. Mik's parts layout allows for ply foils, but not the full-length daggerboard (not enough space in the excess for the full length) so he provides an alternate profile shape. That might be a better route than using undersized timber.
My foils were made up of very inexpensive and lightweight "white wood" pine--lots of pinhead knots--from Home Depot, with a stave of DF up the center and oak on both leading and trailing edges. I thicknessed them by hand (belt sander + 30-grit paper) to 25mm before working the foil shape with a plane. I feel the thicker blank gave me more peace of mind; starting with the exact dimensions would have stressed me out as I removed more and more material. For some reason, the foils were for me the single most psychologically challenging parts of the build. I retrospect I can't say why.
Let us know how you proceed.*
*You might consider starting a build thread too so that we can follow your progress independently of Tippy Canoe's.Dave
StorerBoat Builder, Sailor, Enthusiast
Dave's GIS Chronicles | Dave's Lugs'l Chronicles | Dave's StorerBoat Forum Thread
-
20th February 2013, 02:52 AM #10Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
Build Thread
I'm sure I will start an independent build thread when I actually start to build. I'm in that thinking stage before I actually start to spend $$$ on lumber, plywood and parts. I like to sort as much of this in my head as I can before jumping off the deep end.
davlafont - the mast and dagger board currently seem a bit daunting. When I actually lay my hands on things, I might feel a bit better about it.
Jerry
-
20th February 2013, 07:25 AM #11Senior Member
- Join Date
- Sep 2011
- Location
- Gothenburg, Sweden
- Posts
- 100
GIS lumber
Sorry, I misunderstood you. I haven't come to foils, mast and spars yet, but my plan is to make the foils out if spruce (picea abies) which is the cheap wood you can get anywhere in my part of the world. Most is soft and full of knots, think "Christmas tree", but if you sort out the straight and relatively knot free, I think it's suitable for this type of construction. For the foils the 24mm is important, not for strength as much as that's the thickness needed to get the shape specified (and I hear it's a good shape). My idea is to get wood that is at least 24 mm, cut it into staves (avoiding the bigger knots by cutting those parts away) glue the staves together (with hardwood at the ends) and then find a thicknesser somewhere to get a 24mm thick blank so I have something straight to start with. For spars I have an old mast that I think will do (straight slow grown spruce) and for the mast I see no other option than to go to a real lumberyard and get the good stuff (slow grown spruce for me then) in the specified dimensions. Any decent lumberyard will plane a board down to the size you want. You have to pay for the board they started with and for the job, but the mast is not that much wood so It can't be that expensive?
-
20th February 2013, 07:28 AM #12Senior Member
- Join Date
- Sep 2011
- Location
- Gothenburg, Sweden
- Posts
- 100
GIS lumber
Or 22mm if that's the correct number. In my head it's 24, but I don't have the plans near me, and I suck at remembering numbers for some reason.
-
20th February 2013, 09:16 AM #13Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
I'm the other way around, I can remember numbers but not names. But I suck at math so go figure. 22 mm is correct.
I have a friend who can find anything so I have him working on it.
You can never have too many friends.
-
21st February 2013, 02:48 AM #14
I had a bunch of 19mm cedar, so I cut it into 19x25mm strips to build up the centerboard and rudder to the called-for dimensions. It requires more epoxy to glue up the blank but there's no other downside.
-
24th February 2013, 11:53 AM #15Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
I think that is where I am headed. I have to check and see what the actual dimensions are of WRC here. They may actually not make 19 mm.
Similar Threads
-
Lumber Bunker
By groeneaj in forum TIMBERReplies: 8Last Post: 8th January 2010, 05:04 PM -
The Lumber Yard
By pawnhead in forum Links to: BOOKS, VIDEOS & PLANSReplies: 3Last Post: 15th September 2007, 10:20 PM -
Lumber Bunker
By Luthier in forum WOODWORK - GENERALReplies: 7Last Post: 10th May 2007, 05:00 PM -
The Lumber Bunker
By Lumber Bunker in forum Links to: WEB SITESReplies: 0Last Post: 17th July 2006, 10:15 AM -
Lumber Wizard? - Anybody
By vsquizz in forum HAND TOOLS - POWEREDReplies: 15Last Post: 10th July 2005, 11:13 PM