Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Broken spindle connector
-
6th November 2013, 05:23 PM #1GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
Broken spindle connector
The male plug that goes into the spindle (800W model) has a broken strain relief. My fault trying to install a larger diameter cable than it was designed for.
Does anyone know a source for these connectors? They are the same pin spacing as the 4 pin microphone connectors that Jaycar sell but at380220V andseveral5 amps, I don't think I'd like to use one.
As I have to remove the socket to add an earth wire to the spindle, I'm OK with replacing the connector with another, suitable one.Geoff
The view from home
-
6th November 2013 05:23 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th November 2013, 06:00 PM #2SENIOR MEMBER
- Join Date
- Feb 2008
- Location
- Australia
- Posts
- 988
Element-14 or RS should have a good variety of plugs.
au.element14.com.au
RS Australia | World Leading Distributor of Electronics, Electromechanical and Industrial Components
One I found with a quick search which might be a suitable replacement.
HA4-FK-TE-PM-P-M20 - EPIC - KIT, PANEL MOUNT HA4 4 WAY | element14 Australia
-
6th November 2013, 08:03 PM #3GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
Ch4is,
I have a couple of these plugs/connectors on hand but they would require modification to the spindle to use, as would the square ones you showed.
While I did say I'd be willing to make such modifications, the way my metalwork is going these days, a straight replacement may be saferGeoff
The view from home
-
7th November 2013, 12:43 AM #4
Have a look at this thread as well.
I use the Amphenol plugs because they are power rated for use on the spindles and also they are MUCH better quality than the one the spindles come with. You don't have to solder them either and they can also take a much bigger wire.Bob Willson
The term 'grammar nazi' was invented to make people, who don't know their grammar, feel OK about being uneducated.
-
7th November 2013, 01:01 AM #5
-
7th November 2013, 01:28 AM #6GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
A quick measurement of the Amphenol socket shows it would need at least a 23mm hole, the existing hole is 16.5mm.
Bearing in mind that my spindle is water cooled, there may not be enough room to bore it out
I'll have a closer look tomorrow.Geoff
The view from home
-
7th November 2013, 10:25 AM #7
-
7th November 2013, 03:53 PM #8GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
Took the spindle apart and measure and I agree that the Amphenol socket will fit.
the new hole will just hit the 4 mounting holes for the existing socket. I'll have to drill/tap an aditional hole for the earth wire - it was using one of the existing screws.Geoff
The view from home
-
9th November 2013, 06:56 PM #9GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
5 minutes on the lathe to bore out the hole to 22mm, 10 minutes to drill and tap 2 mounting holes. (not as straight as I'd like )
And there's enough of the tapped holes for the original connector left that I can still use one to attach the added earth lead.
thanks for the suggestion, less painful than I thought it would be.Geoff
The view from home
-
10th November 2013, 07:38 PM #10
Hopefully problem solved. Good luck with reassembly. Reading through I was about to offer a loan of chassis punches to open the hole out, but remembered that you had a lathe in the kit.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
Similar Threads
-
CMS Y connector on CT Midi
By jaydee in forum FESTOOL FORUMReplies: 2Last Post: 10th October 2012, 10:46 AM -
guide rail connector
By fubar in forum FESTOOL FORUMReplies: 1Last Post: 29th September 2011, 11:53 PM -
dinse connector were to buy
By welder in forum WELDINGReplies: 3Last Post: 25th January 2011, 05:37 PM -
Brass connector bolts
By cultana in forum WOODWORK - GENERALReplies: 8Last Post: 5th November 2009, 01:39 AM -
broken plane, broken heart
By fletty in forum HAND TOOLS - UNPOWEREDReplies: 17Last Post: 15th July 2007, 01:55 PM