Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 23 of 23
Thread: Feeds & speeds
-
15th January 2012, 07:25 PM #16
set the z tool hight buy using the "the peace of paper method " , lay a peace of paper on part of the job that will remain when you start , lower the z axis until it just gips the paper( zero the z axis) , when you change your bit you can do it again
an electric z height setter is best but , a peace of paper works
the ball screws will act like worm drives, where its near on imposable to get the ball screw to turn by pushing on the spindle
-
15th January 2012 07:25 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th January 2012, 04:41 PM #17
Here is a chart that I got from NMIT where i do fitting and turning.
Use this as a general setup and tune the cutter to the material being cut.
https://www.woodworkforums.com/f65/mi...9/#post1228064
/M
-
18th January 2012, 05:05 PM #18SENIOR MEMBER
- Join Date
- Sep 2008
- Location
- Maryvale, Queensland
- Posts
- 2,338
Pen Affair Craft Supplies - Cheapest Pearl Ex & Pemo Polymer Clay in Australia
http://craftsupplies.penaffair.com
-
18th January 2012, 05:22 PM #19
The idea is to say pick aluminium and use this as a reference for wood.
Try it on the material you have for the cutter size you want to use.
Its a place to start, then you would tailor the speed up and down and maybe by the time you finish you can make your own chart up which is specific for wood.
No one i know of has anything specific for wood, so this was a means to give you a place to start
-
18th January 2012, 08:03 PM #20SENIOR MEMBER
- Join Date
- Sep 2008
- Location
- Maryvale, Queensland
- Posts
- 2,338
Pen Affair Craft Supplies - Cheapest Pearl Ex & Pemo Polymer Clay in Australia
http://craftsupplies.penaffair.com
-
18th January 2012, 09:05 PM #21
yer its the real fine bits that need the high speed
bit like pen polishing to roughing out 2 foot round bowls
a double cut steel with tungsten tip router bit is designed for 20,000+ , a 10mm mill bit isnt, if the cut is burnished the rev's are too high/ feed rate too slow , ripping up grain the rev's are too slow / feed rate too high !!!!or blunt !!! , bit / speed / material , there is too many variables like knots
brake a bit , well thats just operator error broke a 2mm ball nose tonight no rev's air cut , into the base aluminium , " PING" machines fault i say it is , the machine dosnt have limit switches yet yer yer , 500 mm depth is my fault ??? 50 mm ??? my first berry it into the table and move x back and forth to bore , at least the bit wasn't spinning just a scratch
-
18th January 2012, 09:53 PM #22
Details here, including chip loads for different materials:
Calculating Feeds and Speeds - CNC Router Shop
http://www.cncroutershop.com/media/u...utterguide.pdf
-
19th January 2012, 10:10 AM #23Member
- Join Date
- Jul 2009
- Location
- Detroit, Michigan
- Age
- 60
- Posts
- 72
You'll probably need to convert the chiploads into mm's, but if you find an Onsrud tool that's similar to what you have, they'll have a feed and speed for it.
Chiploads | Feeds and Speeds | Metal | Plastic | Composite | | LMT Onsrud
Similar Threads
-
Speeds and Feeds for cutting corian
By phomann in forum CNC MachinesReplies: 2Last Post: 16th June 2010, 08:38 AM -
Rss feeds
By Shuttle in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 0Last Post: 14th February 2009, 06:40 AM