Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
Thread: Homing.....totally confused
-
1st November 2008, 02:31 PM #1
Homing.....totally confused
Hi all,
I'm having some trouble understanding the homing/limits setup. My BIG problem, is trying to figure out where X0Y0 is supposed to be (specific to a gantry router).
If I stand at the front of my machine (as per picture), I was trying to set X0Y0 to the top left corner. I can set this up okay, and the DROs all work correctly. However, when I set a work offset (G54), Mach seems to want it's X0Y0 at the bottom left corner of the work. When I do this, +Y goes in the right direction, but +X goes the wrong way. So if you load the Roadrunner, the tool comes off the work when it traverses X. Am I supposed to be setting home at bottom left?
If someone with a gantry machine can explain, it would probably help me save some of the little hair that I have left. A screenshot of your homing/limit screen would be very nice too.
I went onto the Vectric site today, to purchase Cut2D. They are using an exchange rate of 0.56, compared with current 0.669. I tried to order in US$, as Paypal is using the correct exchange rate, but they are still trying to bill me in AU$. This adds AU$43 to the cost . I've sent them an email, and hope they will fix the issue before I continue with the purchase. I haven't found an alternative site to purchase from, so I might be stuck with a crap rate when I buy.
Thanks for any help.Chris
========================================
Life isn't always fair
....................but it's better than the alternative.
-
1st November 2008 02:31 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
1st November 2008, 04:06 PM #2SENIOR MEMBER
- Join Date
- May 2005
- Location
- Cockatoo Vic
- Posts
- 996
Chris
I just tried the Vectric site and it appeared to let me pay in UK pounds.
Using UK pounds seems to be a better deal at the moment.
Regarding X and Y origin,
It does not matter what side of the machine you decide to think of as the front.
Once you decide that, then the X and Y origin is at lower left, or closest to you and to your left as you stand in front of it.
Going by your pic, as you stand in front then the direction that the whole gantry moves, towards and away from you is the Y axis. Zero closest to you and going in a positive direction as it moves away.
The spindle moving along the length of the gantry is the X axis. Zero when all the way to your left and going in a positive direction when moving to your right.
If using home switches, convention has them at the zero end of travel but with Mach they can be at either end, does not matter. Just another setting.
If it would help PM me we can talk by phone.
Greg
-
1st November 2008, 05:40 PM #3
Thanks Greg,
Silly Muggins here, had X & Y transposed in his mind.
I've reconfigured, and it makes sense on the screen. I'll plough on again, and see how I go. Thanks for the offer of the phone talk, I might take you up on that down the track.
I'll have another look at Cut2D in Pounds sterling.Chris
========================================
Life isn't always fair
....................but it's better than the alternative.
Similar Threads
-
How to get this surface totally flat?
By wixy in forum WOODWORK - GENERALReplies: 17Last Post: 3rd April 2007, 11:22 PM -
Totally off topic but...
By Marchalis in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 0Last Post: 6th September 2006, 03:06 AM -
totally awesome website
By goat in forum Links to: WEB SITESReplies: 3Last Post: 4th August 2005, 08:46 PM -
Totally OT:- Cameras
By CountTFit in forum ROUTING FORUMReplies: 1Last Post: 14th August 2002, 08:09 PM -
Totally Wooden Clocks
By Dod in forum WOODWORK - GENERALReplies: 6Last Post: 27th January 2001, 05:01 PM