Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 2 of 2
Thread: Huanyang VFD and Spindle motor
-
27th October 2012, 08:32 AM #1New Member
- Join Date
- Oct 2012
- Location
- California
- Posts
- 1
Huanyang VFD and Spindle motor
Hello everyone,
I recently got the DIY CNC itch, and I just couldn't help it...I had to scratch.
It started about 1-1/2 year ago and I worked on a project, codename "Angry Termite" it on and off; when it got too frustrated I left it alone and worked on some other project, and I went back with when I found a solution for the cause of the frustration. So, after all this time, I finally finished it: a 3 axis, 80/20 structural aluminum frame CNC router which I run using Mach3.
A month or so ago, I started reading on CNC forums about been able to control spindle speed, pumps/vacuum machine on/off, etc. So I purchased a Huanyang VFD with its corresponding spindle motor. I live in sunny California, and as you probably already know, we have, 110V for domestic use, and for heavier duty work 220V.
I am not an engineer, only a chemist, but I have a natural ability to absorb this type of knowledge and figure out things on my own, but to keep it simple, I chose a 110 V VFD and 110 V water cooled 0.8 kW spindle motor (I knew I should have been a mechanical engineer!)
After going back and forth with the ebay vendor for a good 10 days (mostly due to a language barrier) about receiving a defective unit (the right digit on the display was kaput, DOA), and a motor that showed clear signs of being a used one (in spite of it being sold as new), I managed to setup the main PD parameters, hooked everything up, gave it juice and to my surprise, everything worked! The spindle spooled up like a jet turbine!
I can't remember the exact PD settings, but the display climbs up to 400hz, and max RPMs 19520. Now here's a couple of questions:
- The AC input is single phase 110V (live, neutral and ground), the output, or spindle input, are 3 wires but none of them is a ground. Which is the best way to connect a ground to the spindle? Do I just run a ground wire from the VFD terminal and secure it to the motor input connector with some type of clamp?
2. I understand that I should be able to run the motor to a max of 24,000 RPMs, but is this limitation due to the use of single phase 110v, or is there a PD setting that I missed?
Yeah, I read the manual that came with it, but my Chinese is not that good...In fact, I don't speak it! (but I found the English version. Confusing as hell, though)
Cheers,
Gustavo
-
27th October 2012 08:32 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th October 2012, 08:18 AM #2
Hello gustavo and welcome to the board.
The best way to ground the spindle is to run a wire from the spindle case to your power ground. This can be done by drilling and tapping or drilling and bolting through the very hard stainless teel casing, or you could just clamp the wire between the motor end cover and the casing.
As to the rest of the settings, I offer this link for you to read. I would tell you exactly what part I think you should go to, but you will learn a hell of a lot more if you read the whole thing.Bob Willson
The term 'grammar nazi' was invented to make people, who don't know their grammar, feel OK about being uneducated.
Similar Threads
-
Huanyang VFD and 2.2kw spindle
By naijin in forum CNC MachinesReplies: 2Last Post: 23rd October 2012, 07:53 AM -
Spindle Motor Specs
By WoodPleb in forum CNC MachinesReplies: 9Last Post: 29th June 2012, 02:19 PM -
Spindle speed control, Huanyang VFD and DC-03
By Bob Willson in forum CNC MachinesReplies: 62Last Post: 20th September 2010, 10:59 PM -
Spindle motor
By chrisb691 in forum CNC MachinesReplies: 47Last Post: 2nd December 2009, 11:55 PM