Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 21
Thread: Looking For Materials
-
7th December 2008, 01:57 PM #1
Looking For Materials
Some of the machines on the net have work tables with T slot aluminium extrusions.
Any clues where to look in Oz?
Also looking for suppliers of Aluminium tube - round & square.
-
7th December 2008 01:57 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
7th December 2008, 03:51 PM #2
I got some from here http://www.woodworksupplies.com.au/category73_1.htm
A couple of photos installed are here https://www.woodworkforums.com/showpo...4&postcount=40
-
7th December 2008, 07:11 PM #3
Hi John,
Which clamps did you order with the track?
The site is not too clear in that area.... I have sent him a message
-
7th December 2008, 07:44 PM #4
I got a couple of the Incra hold down clamps and use these in combination with 1/4 bolts and washers to hold down work pieces.
I'm pretty sure the site had photos when I ordered as I'm normally fussy about seeing photos of what I'm ordering. I think they are the ones called HD Pivot Hold Down Clamp (Incra). http://www.woodworksupplies.com.au/category77_1.htm
-
7th December 2008, 07:53 PM #5
Try capral I find they have a good range and the cost if fair
Ashore
The trouble with life is there's no background music.
-
7th December 2008, 08:03 PM #6
-
7th December 2008, 08:48 PM #7
Bob
i used aluminium profiles for my machine - just Goggle "MiniTec"
I don't know who sells it in Victoria but i got mine through SPC in adelaide and i am sure they have their head office in melb.
Cheers
Noel
-
7th December 2008, 08:51 PM #8
look in the phone book under aluminum supplies there are plenty of places around that sell it.
www.carlweiss.com.au
Mobile Sawmilling & Logging Service
8" & 10" Lucas Mills, bobcat, 4wd tractor, 12 ton dozer, stihl saws.
-
7th December 2008, 08:51 PM #9
-
7th December 2008, 09:02 PM #10
-
8th December 2008, 09:30 AM #11SENIOR MEMBER
- Join Date
- May 2005
- Location
- Cockatoo Vic
- Posts
- 996
I like the look of these to go with the tee slot.
-
8th December 2008, 02:14 PM #12
-
8th December 2008, 02:59 PM #13
-
8th December 2008, 04:05 PM #14
I'm aware the wigits are custom made, but I recall seeing somewhat similar extrusions to the work table top some years ago.
-
8th December 2008, 05:01 PM #15
Similar Threads
-
Router table materials
By Alastair in forum ROUTING FORUMReplies: 21Last Post: 10th December 2008, 04:19 PM -
Router Table Materials
By djfoggin in forum ROUTING FORUMReplies: 25Last Post: 12th May 2007, 08:58 AM -
Alternate Materials
By Rance in forum WOODTURNING - PEN TURNINGReplies: 7Last Post: 4th May 2007, 04:14 PM -
Brisbane Materials
By ptyltd in forum Links to: TIMBER & HARDWARE SUPPPLIERSReplies: 2Last Post: 13th January 2006, 01:51 PM