Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Wire Marking
-
18th November 2010, 06:17 PM #1Senior Member
- Join Date
- Apr 2009
- Location
- Kingswood
- Posts
- 422
Wire Marking
I am re-wiring a Kondia mill with spindle VSD, improved lubrication to slideways and ballscrews, knee gas springs, E-Stop buttons, limit switches etc.
For the new wiring in the panel, I want to include wire numbers.
Not one of the electrical wholesalers in Penrith stock numbered ferrules.
The modern practice is not to number the wires if you can get away with it, or make generated sleeves on demand if mandatory.
The wiring is simple, and doesn't really need numbering, but it would be 'nice'.
I am considering white heat shrink tubing, an indelible ink pen, hand-written numbers and then heat applied.
Any recommendations for a single core wire numbering scheme (cheap !) ?
Happy machining,
John.
-
18th November 2010 06:17 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
18th November 2010, 07:47 PM #2
Roughly how many numbers are you looking at John?
We use an on demand printing system at work. I don't think anyone stocks individual numbers any more. Just not economical.Those were the droids I was looking for.
https://autoblastgates.com.au
-
18th November 2010, 08:18 PM #3Senior Member
- Join Date
- Apr 2009
- Location
- Kingswood
- Posts
- 422
Hi NCArcher,
Thanks for the suggestion.
My situation is not too many wires at all, but not worth getting anyone to provide a service.
It is just interesting that there is not something available.
I can remember purchasing 10 rolls of numbered adhesive tape in a holder (numbers 0 - 9).
This was small enough to carry in the toolbox and a convenient way to identify changes in the field.
One just cut off a length and wrapped it around the core.
Perhaps all field guys these days carry a labelling machine ( or don't bother ).
Bigger than my 10 rolls (but not by much), but doable.
Modern technology provides an accurate, current, schematic on the screen of the inevitable laptop, so wire numbers to trace connections could be regarded as redundant.
My current mill build is not permanent, it is a hotch-potch of boxes and bits just to get the mill operating.
I will give it some time to sort out problems and the inevitable additions, then integrate into a single cabinet.
John.
-
19th November 2010, 02:53 AM #4GOLD MEMBER
- Join Date
- May 2003
- Location
- Perth WA
- Posts
- 3,784
-
19th November 2010, 08:59 AM #5SENIOR MEMBER
- Join Date
- Feb 2008
- Location
- NOWRA
- Posts
- 648
The above link is what is used for cable marking but when you say single core wire marking the standard in industrial switchboards are one of two things. During install there are wire ID kits which are numbers on sleeves which are installed onto the wire as identifiers (see pic below). The other can be installed after wiring and clips onto the wires and has a small pocket at the top that pre-printed numbers are slipped into. Can't seem to remember the proper name for them but when i do will post a piccy. Both are very reliable.
Daniel
-
19th November 2010, 07:00 PM #6
In the past I have printed numbers, descriptors etc on plain paper on a normal computer, trimmed to suit, inserted the lable into clear heatshrink, placed the label subassembly on the wire and shrinking in place.
An updated approach might be to print onto full sheet label stock instead of plain paper, and rely on the adhesive back to hold the label in position prior to shrinking.
Similar Threads
-
EDM wire cutting
By Enfield Guy in forum METALWORK FORUMReplies: 5Last Post: 10th September 2009, 06:01 PM -
marking set
By weisyboy in forum WOODWORK - GENERALReplies: 12Last Post: 29th January 2009, 09:57 PM -
Mig Wire Question
By iron bark in forum WELDINGReplies: 8Last Post: 19th March 2007, 07:08 PM -
A box for a marking set
By derekcohen in forum BOX MAKINGReplies: 22Last Post: 13th December 2006, 10:55 PM