Thanks Thanks:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 7 of 7
  1. #1
    Join Date
    Oct 2007
    Location
    Sydney
    Age
    66
    Posts
    140

    Default Repair to cocktail cabinet door - advice needed please

    Hi all,

    My daughter has a cocktail cabinet with veneered particleboard doors. According to her it is a "mid-century classic".

    This is the daughter who, at the age of 7, asked me to make a table for her teddy bears out of offcuts from a deck I'd just finished building. I gave her a little lecture about how you should always "measure twice, cut once", then immediately made a cutting mistake. She looked up at me and said, deadpan, "Daddy shouldn't that be 'measure thrice, cut twice?'". She later majored in linguistics.

    Anyway, the particleboard has split and crumbled where the screws for the hinges go into the top and bottom edges.

    Image 1 shows the veneer which is bent but not broken.
    Images 2 and 3 show how the top corner is damaged
    Image 4 shows the bottom corner, which is splitting but not as badly as the top corner.

    So what are my options? Soak the damaged parts is some sort of glue then clamp to the right thickness? Cut out the disintegrated part and slot something else in?

    I am in your expert hands.

    Thanks in advance.
    Attached Images Attached Images
    • File Type: jpg 1.jpg (208.8 KB, 10 views)
    • File Type: jpg 2.jpg (112.2 KB, 10 views)
    • File Type: jpg 3.jpg (128.3 KB, 7 views)
    • File Type: jpg 4.jpg (141.5 KB, 7 views)
    Measure thrice, cut twice.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    Apr 2014
    Location
    Little River
    Age
    77
    Posts
    1,205

    Default

    You could try Chair Doctor glue as it will soak right in. Put the glue on then quickly clamp the panel.

  4. #3
    Join Date
    Jul 2008
    Location
    geelong
    Posts
    359

    Default Chipboard

    First thoughts would be much like yours - take it to the tip. However you seem to have the right idea Rake out the loose stuff Fit a bit of hardwood and with lots of glue glamp to thickness then clean up re-veneer etc. Still chipboard rubbish but one repaired a "art deco" desk that sold for $8000 .

  5. #4
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    4,470

    Default

    Just fill with PVA and clamp with suitable blocks and baking paper on the veneer so glue does not stick

  6. #5
    Join Date
    Oct 2007
    Location
    Sydney
    Age
    66
    Posts
    140

    Default

    Baking paper - a great tip.

    I watched a video showing a guy sawing out a thin kerf to allow clamping to get it back into line. Youtube video "[COLOR=var(--ytd-video-primary-info-renderer-title-color, var(--yt-spec-text-primary))]Swollen Particle Board Repair Veneer faced." [/COLOR]Maybe I'll do a test run clamping it dry to see if I need to remove some material.
    Measure thrice, cut twice.

  7. #6
    Join Date
    Aug 2010
    Location
    ACT
    Age
    84
    Posts
    2,578

    Default

    Hi,
    This is only a suggestion, not something I have done.
    Glue up as suggested above then when set and dry drill and insert a dowel side ways on just blow the screw holes so that the screw will enter the cross grain of the dowel. Drill pilot holes through the dowel so the whole thin does not happen again while you are screwing up.
    Best of luck
    Regards,
    Hugh

    Enough is enough, more than enough is too much.

  8. #7
    Join Date
    Oct 2007
    Location
    Sydney
    Age
    66
    Posts
    140

    Default

    Quote Originally Posted by A Duke View Post
    Hi,
    This is only a suggestion, not something I have done.
    Glue up as suggested above then when set and dry drill and insert a dowel side ways on just blow the screw holes so that the screw will enter the cross grain of the dowel. Drill pilot holes through the dowel so the whole thin does not happen again while you are screwing up.
    Best of luck
    Regards,
    Good idea re the dowel. I guess the main problem with cocktail cabinet doors is that people are opening and closing them after a few cocktails. So giving the screws something to grab onto would be a win.
    Measure thrice, cut twice.

Similar Threads

  1. Cabinet Door and Chair Leg repair
    By IvanOz in forum GLUE
    Replies: 4
    Last Post: 11th May 2015, 01:09 AM
  2. Replies: 8
    Last Post: 18th August 2014, 03:52 PM
  3. Gear repair, advice needed.
    By Com_VC in forum METALWORK FORUM
    Replies: 11
    Last Post: 25th August 2012, 02:12 PM
  4. Finish on old cocktail cabinet
    By Shiba in forum RESTORATION
    Replies: 5
    Last Post: 7th August 2008, 10:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •