Page 1 of 2 12 LastLast
Results 1 to 15 of 30
  1. #1
    Join Date
    Jun 2019
    Location
    Lennox Head
    Posts
    2

    Default Restore Parker Mid Century Teak table top

    I have a 60s teak table which I would like to restore. It has some much darker colours in some of the grain. I don't know what has caused this but I would like to even it out if possible.
    Attached Images Attached Images

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    May 2011
    Location
    Albury
    Posts
    3,019

    Default

    Just by looking at the edging I can tell this is a veneer top. It's likely to be pretty thin and any vigorous sanding will risk rubbing right through it. The table looks to be in pretty good condition so a light sand followed by the finish of your choice would be my recommendation. The dark patches in the grain give the top character, I like it.

  4. #3
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,649

    Default

    Quote Originally Posted by magfowl View Post
    It has some much darker colours in some of the grain.
    That is the very nature of Teak grain. What you are seeing is a veneer from across the log.

    The "triangular" part in pic #3 is showing the darker part very nicely. That part is "backsawn" which means the saw cut runs down the growth ring. That sort of cut yields very wide grain patterns.

    Then, on either side of that, you can see that the growth rings are cut in profile. This part is "quarter sawn". So in those parts you can see that the grain lines are much straighter and are about 6-10mm apart. Some of those lines are dark.....so imagine if the saw cut went down into the log following that dark line in.....you would have the same sort of grain as in the middle - the triangle.

    Sorry if that is a bit of a clumsy explanation.

    In any event, the grain colour is what it is, and that was the whole attraction of Teak.....
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  5. #4
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,649

    Default

    Have a look at some of the images here:
    https://www.google.com/search?client...r+quarter+sawn

    and think about how the grain would respond to those cuts.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  6. #5
    Join Date
    Dec 2010
    Location
    Mornington Peninsula
    Posts
    2,741

    Default

    I thought that all Parker Furniture was solid wood, and typically from the 1970’s.

  7. #6
    Join Date
    Aug 2004
    Location
    Perth WA
    Posts
    2,035

    Default

    Quote Originally Posted by cava View Post
    I thought that all Parker Furniture was solid wood, and typically from the 1970’s.
    No it was/is veneered chipboard and early non water resistant stuff. With this one the edges are the giveaway.
    Experienced in removing the tree from the furniture

  8. #7
    Join Date
    May 2011
    Location
    Albury
    Posts
    3,019

    Default

    My mother has a Parker table of that vintage cava and it definitely has a veneer top. Lots of their sideboards, book cases and wall units are also veneer. FenceFurniture has the explanation as to why the top looks as it does spot on.

  9. #8
    Join Date
    Dec 2010
    Location
    Mornington Peninsula
    Posts
    2,741

    Default

    I stand corrected guys. The things you learn.....🤐

  10. #9
    Join Date
    Aug 2011
    Location
    bilpin
    Posts
    3,551

    Default

    Rotary peeled Burmese teak veneer, laid on veneer grade particle, before the days of MR particle board. Used to supply them with tons of the stuff.

  11. #10
    Join Date
    Nov 2010
    Location
    Perth W.A
    Posts
    720

    Default

    This is a typical piece of mid-century furniture with crown cut veneer. Despite it being very expensive at the time was usually quite cheaply made with normally a particle board carcase and some solid lippings. Sometimes the particle board ends up like Weet-bix if exposed to the damp. The leaves of the table are darker and have a fresher appearance to the rest of the the table due to having spend most of their life folded away.

    The veneer will be quite thin (0.5 mm or so) if you are sanding then probably no coarser than 240 grit to start and then refinish with Danish oil or similar.

  12. #11
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,649

    Default

    Quote Originally Posted by rustynail View Post
    Rotary peeled Burmese teak veneer,
    I had typed that it was Rotary peeled, but then I thought "It can't be" because it goes from backsawn to ¼sawn in the same veneer which surely means it's a flat veneer from across the log. Isn't rotary peeling the equivalent of back sawn all the way across the sheet - no possible to show ¼sawn?
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  13. #12
    Join Date
    Apr 2013
    Location
    Macksville
    Age
    62
    Posts
    390

    Default

    I've got a similar one (not sure of brand) that I've been asked to fix up for the local Cranky Womens Association. I was going to give it a sand & refinish it with WOP, but the veneer is so thin it's worn through to the chipboard in a couple of places, so looks like it's going to get a couple of coats of CWA navy blue paint.

  14. #13
    Join Date
    Jun 2019
    Location
    Lennox Head
    Posts
    2

    Default

    Thank you for all that information about my table and thank you also for taking the time to reply.

    Now what will I do with the table? What is WOP? I don't think I will use CWA navy blue paint. I looked at Feast Watson Scandinavian Oil. After a fine sand or perhaps 0000 steel wool could I use this or is there something better.

  15. #14
    Join Date
    Aug 2011
    Location
    bilpin
    Posts
    3,551

    Default

    Quote Originally Posted by FenceFurniture View Post
    I had typed that it was Rotary peeled, but then I thought "It can't be" because it goes from backsawn to ¼sawn in the same veneer which surely means it's a flat veneer from across the log. Isn't rotary peeling the equivalent of back sawn all the way across the sheet - no possible to show ¼sawn?
    Veneer laid on particle board is not one full width of veneer across the whole sheet. The veneer is made up of strips, taped together to form a suitable pattern, preferably as close to book matching as possible. These veneer strips vary in width from different manufacturers but about 300mm is the norm. By using rotary peel in conjunction with alternate sliced strips gives the impression of a true sliced veneer. In other words, a cheaper imitation of the real thing. Full width sliced veneers would be pretty costly.

  16. #15
    Join Date
    May 2007
    Location
    Sth Gippsland Vic
    Posts
    4,355

    Default

    It doesn't look like full rotary peeled though .
    They would swing a log through an arc and get longer width slices which probably gets it looking slightly more towards a peeled look . The Half round slicing in this picture. Maybe its that . The crown in that veneer looks slightly off the norm. But nowhere near as Ugly as rotary peeled.

    Looking again , I think the only reason it looks slightly off the norm is the way they joined the slices at the crown part the way they did. Its just normal sliced veneer in the half round or flat slicing .

    IMG_1528.JPG

Page 1 of 2 12 LastLast

Similar Threads

  1. Clean & Restore Teak Parker Chairs
    By mtchairs in forum RESTORATION
    Replies: 5
    Last Post: 3rd October 2014, 08:39 PM
  2. Restoring a Parker table
    By Cobralico in forum FINISHING
    Replies: 0
    Last Post: 12th July 2013, 11:39 AM
  3. Restore Teak Outdoor Table
    By Off the Block in forum RESTORATION
    Replies: 2
    Last Post: 9th May 2010, 06:03 PM
  4. restore a teak table/oil residue
    By ozbeat in forum FINISHING
    Replies: 5
    Last Post: 13th April 2007, 08:32 PM
  5. How to restore Creasote & klinky(marine ply) ? and teak
    By Zrichard in forum GENERAL ODDS N SODS
    Replies: 2
    Last Post: 19th September 2004, 11:45 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •