Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 5 of 5
  1. #1
    Join Date
    Jan 2009
    Location
    melbourne
    Posts
    4

    Post Rifle Stock Issue

    Hi all Any Ideas on how i can remove some marks from my riflestock? The stock has had all varnish removed and i've floated the barrel. I've tried using a damp cloth with a hot iron, and that worked on most of them, but i have some on the Butt of the rifle that seem to be a little too deep. Posted a pic for you guys to have a look at.
    Thanks All
    gate7

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Feb 2007
    Location
    blue mountains
    Posts
    4,882

    Default

    I reckon the deep ones that the iron cant get will just have to stay. It just shows that the gun has had some use. It does not look bad and will not affect anything. There is a small chance that soaking the dented part with a wood oil will swell the fibers a bit but no guarantee. Wet a rag with the oil and wrap it on with clingwrap for a few days. It will not hurt anything if it does not work.
    Regards
    John

  4. #3
    Join Date
    Jan 2009
    Location
    melbourne
    Posts
    4

    Default

    Cool thanks orraloon,
    One more thing, I'm going to use Tru-oil on the timber, what about the inside where the barrel sits and around the magazine and trigger? Would i have to seal those areas also? I think i should moisture can get in there also correct? should i use tru-oil in there also, sorry for the noob questions

    Cheers
    gate7

  5. #4
    Join Date
    Feb 2007
    Location
    blue mountains
    Posts
    4,882

    Default

    From memory as I have not owned a gun in 25 years I have seen both sealed and dry wood. My instinct as a woodworker says seal the insides too but it may be prudent to seek the advice of a gunsmith before slopping away. A bit of gun oil is always going to seep in there also. I have also seen a badly twisted stock from being left hot car.
    Regards
    John

  6. #5
    Join Date
    Feb 2007
    Location
    Katherine ,Northern Territory
    Age
    69
    Posts
    1,977

    Default

    My take on it is , if the barrel is fully floating (not touching the stock anywhere between the receiver and the fore end tip then you can leave it unfinished if you want to. Most older factory rifles had the timber touching the barrel at the fore end tip to exert a slight upward pressure on the barrel to curb vibration when the projectile travels down the barrel .This set up is fine in a situation where the weather doesn't change .
    But where there is drastic changes between dryness and humidity this will cause the timber of the stock to move , upsetting the balance (for want of a better word) of the barrel /stock relationship.

    So If the barrel is not floated then I would seal it.Easy way to check is get a cigarette paper and try and pass it between the barrel and the stock at the fore end.If it gets stuck then you have contact between the barrel and the timber.

    The other option is to bed the action into the stock with fibre glass or epoxy resin and float the barrel .
    Either way I would seal it anyway ,as I used to hunt in wet and dry weather ,any moisture held by the timber under the barrel would cause rust.


    BTW Tru-oil is the "ducks" nuts for rifle stocks follow the directions and you can't go wrong there.

    Kev
    "Outside of a dog a book is man's best friend ,inside a dog it's too dark to read"
    Groucho Marx

Similar Threads

  1. Walnut Rifle Stock Surface Preparation & Finish
    By Rabbitz in forum FINISHING
    Replies: 34
    Last Post: 28th October 2008, 08:08 PM
  2. Advice Sought on Rifle Stock Timber
    By Paratus in forum WOODWORK - GENERAL
    Replies: 14
    Last Post: 11th June 2006, 09:19 AM
  3. Head Stock & Tail Stock extention plates
    By Babytoolman in forum WOODTURNING - GENERAL
    Replies: 0
    Last Post: 25th December 2005, 11:37 AM
  4. Rifle pen clips
    By bdar in forum WOODTURNING - PEN TURNING
    Replies: 12
    Last Post: 21st August 2005, 11:42 PM
  5. Rifle pen clips
    By bdar in forum WOODTURNING - GENERAL
    Replies: 0
    Last Post: 25th July 2005, 12:57 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •