Page 1 of 2 12 LastLast
Results 1 to 15 of 16
  1. #1
    Join Date
    Jan 2007
    Location
    Brisbane
    Posts
    696

    Default Trialing Evapo-Rust and Inox Lanox for metal recovery and protection

    Doing this in preparation for some old furniture metal handles in the near future. I lashed out when there was a 25% discount sale going and bought the Evapo-Rust and Lanox.
    Photo 1 is an ice cream container where I try to keep the required volume low.
    Photo 2 - 5 is this first batch of tools after period in Evapo-Rust and then cleaned in water before being sprayed with Lanox to prevent corrosion starting again


    Before rusty.jpgAfter Evaporust.jpgAfter Evaporust 02.jpgAfter Evaporust mulit grip 02.jpgAfter Evaporust mulit grip.jpg

    Later I will move to the different furniture handles that I have found challenging using wire brushes. I hope this helps others make the same trail.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Nice work.

    After being de-rusted I don't wash my items in water because if water gets into a crack or a join and is not adequately displaced by a protectant then it can cause rust.

    I found it better to remove the items from the rust remover and just blow dry with compressed air, or hang in the sun, or use a hot air gun . Some residual dust remover may remain in a powdered form on the surface but that can usually be wiped off.

    A really secure way to get protectant into all the cracks and narrow pathways is to heat up a container of lightweight engine oil and heat the items in the oil for 10 minutes. I use an old electric fry pan with an old sauce pan as the pot. Then I suspend said over the pot so the hot oils drains off the object. Hot oil drains much better from a hot object so it does not leave the object too objectionable. Then I might apply something like Lanotec.

    Evaporust is good stuff but if you want to save a few bob there are plenty of other cheaper options. Plain old vinegar works although it's a bit slow (stronger vinegar works faster), Citic acid is quicker. Phosphoric acid (PA) is quick but its hard to get pure PA as it usually comes with added detergent to help wet the rust but then this has to be washed off and we're back to the water problem again.

    Industrial folks will often use Oxalic acid, although that does leave a yellow/green tinge on the surface - this tinge is VERY antirust so items can be left out for months without rusting and also fine if de-rusted items are going to be painted as it can be directly overpainted. Oxalic acid is available from Bunnings as Diggers Rust and Stain remover.

    Here's a test I did few years ago.
    Items were sanded on a belt sander and then left outside for about a month until they were completely covered in rust and then de-rusted in;
    (L-R) HCl, citric Acid, Oxalic acid and acetic acid.
    This photo was taken 10 weeks after they had been left to hang up outside.
    10weeks.jpg

    The other rust removing agent I like using is tannic acid. It's sold in an expensive liquid form called Fertan that is even more expensive than Evaporust but it's its been around for centuries and is used by museums to restore iron based materials like old tools and farm implements. I bought a kg of food grade Tannic acid powder on ebay for about 1/3rd of Fertan to do a bunch of experiments with. It's fiddly to make and apply, and leaves steel/iron surface a very traditional sooty black colour. The slyer is very anti rust but does come off on a users hands so its not suited to direct use of objects that need to be being handled although it can easily be rubbed off with a light wire brushing or over painted. I really like the dark black look for some tools like this blacksmiths voce so in those cases I apply a coat oil that takes up the soot and polymerises (forms a skin) like linseed oil.

    Here's a before and after on a BS vice.
    The original blue painted vice on the LHS does not look rusty but it was all rust under that paint.
    FinalBSvice.jpg

    The of course there's metal bluing, but that is another large can of worms.

  4. #3
    Join Date
    Nov 2004
    Location
    Redlands area, Brisbane
    Posts
    1,489

    Default

    That vise is a real beauty!

  5. #4
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by markharrison View Post
    That vise is a real beauty!
    I got if from our mens shed - it had been put on the scrap pile.

    Full WIP here.
    BS Vice - restore or retire?

  6. #5
    Join Date
    Jan 2007
    Location
    Brisbane
    Posts
    696

    Default


    Thanks BobL you have accelerated my learning with your experiment results (it was planned )
    I've used Oxalic acid on wood and you just made it all click together. Too much thinking about what others say and not enough experimenting but now you have shown me the light. Oxaic acid will be trialled soon
    I have played with some Coke and getting ready to build some pulsing electrolysis units as well.
    I hope to trial some electroplating as well.

    I have a failed 21A 6/12/24V battery charger that is going to be made into a hefty DC power source and then with add-ons a battery charger and electrolysis unit

    I also have some old vices to clean down and bring back to life and on day will share their pictures.

    Another plan is to build some vibration devices to accelerate so of these reactions

    Many thanks for sharing the valuable information.

  7. #6
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by Blackout View Post
    Thanks BobL you have accelerated my learning with your experiment results (it was planned )
    I've used Oxalic acid on wood and you just made it all click together. Too much thinking about what others say and not enough experimenting but now you have shown me the light. Oxaic acid will be trialled soon


    I have played with some Coke and getting ready to build some pulsing electrolysis units as well.
    I hope to trial some electroplating as well. I have a failed 21A 6/12/24V battery charger that is going to be made into a hefty DC power source and then with add-ons a battery charger and electrolysis unit
    Some battery chargers won't function unless connected to a battery so you will need to over come this. Its good that yours has a 6V capability as that is all that is needed. The current is determined by the concentration of the electrolyte and the physical layout/connections of the work pieces and anodes.
    I've found about 6V and between 3 and 5A works. The 5V outputs of PC power supply is usually good enough.

    More than volts 6V ends up turning more H20 into H2 and O2 which is necessary and dangerous, The excess O2 also destroys any steel anode and turns it into a resistive orange sludge which slows down the process.

    One of the cleanest Anode to use is carbon rods - no orange sludge. These can be obtained from Welding shops - they are usually covered by a thin copper coating which can be peeled off.

    SolutionScum.jpg

    I use sodium carbonate (foot baths salts from Coles) as the electrolyte. The resulting solution can be safely disposed off down the sewers.

  8. #7
    Join Date
    Apr 2019
    Location
    NSW
    Age
    37
    Posts
    1,126

    Default

    any opinions on phosphoric acid?

    i bought this from the big green shed to use as a rust converter on some things in my garage. because my garage is under the house the moisture is a killer and i'm for ever dealing with tools rusting up. I've tried it on a small centre finder i built back as a first year apprentice (will add pics when i get home) and it seems to have done all right. Almost need to coat my table saw cast iron bench in the stuff.

    Bondall 500ml Ranex Rustbuster Rust Converter | Bunnings Warehouse


  9. #8
    Join Date
    Jan 2007
    Location
    Brisbane
    Posts
    696

    Default

    That is such helpful information and gratefully appreciated the sharing of such knowledge. Thank you

  10. #9
    Join Date
    Jan 2007
    Location
    Brisbane
    Posts
    696

    Default

    There is something in the back of my mind about this that will eventually come to me and I'll post.

  11. #10
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by havabeer69 View Post
    any opinions on phosphoric acid?

    i bought this from the big green shed to use as a rust converter on some things in my garage. because my garage is under the house the moisture is a killer and i'm for ever dealing with tools rusting up. I've tried it on a small centre finder i built back as a first year apprentice (will add pics when i get home) and it seems to have done all right. Almost need to coat my table saw cast iron bench in the stuff.
    Phosphoric Acid (PA) is useful stuff, Ranex contains detergent to help it wet the rust but then this needs to be washed off otherwise it dries with a rough surface which can be hydrophilic (absorbs water) and then rusts after being washed. The old Chemtec PA (available from the bunnings building supplies shelf) was better - no detergent and much stronger for less $$ but I note the new Chemtec PA is weaker and has some detergent in it. I reckon Citric and Oxalic are better rust removers with the Oxalic being the best if delisted object is going to be painted.

    Here is an Uber nerdy threat comparing PA with Tannic acid
    Restoring Metal objects and surfaces

  12. #11
    Join Date
    Apr 2019
    Location
    NSW
    Age
    37
    Posts
    1,126

    Default

    I couldnt find any "before photos" but the rust was bad enough that you couldnt make out my engraving. I wouldnt say the surface is smooth but not heaps rough. Its complex things like drill chucks im wondering if i can dunk in the stuff

    20200623_182956.jpg

  13. #12
    Join Date
    Feb 2006
    Location
    Perth
    Posts
    27,756

    Default

    Quote Originally Posted by havabeer69 View Post
    I couldnt find any "before photos" but the rust was bad enough that you couldnt make out my engraving. I wouldnt say the surface is smooth but not heaps rough. Its complex things like drill chucks im wondering if i can dunk in the stuff
    Yes you can dunk it in PA but for something like a chuck the PA needs to be carefully washed out. I would boil it in deinioized water for ~10 minutes. Then the water needs to be displaced so heating the chuck in light engine oil for 10 minutes. This will displace the water and also lubricate the chuck.

  14. #13
    Join Date
    Jan 2014
    Location
    Sydney Upper North Shore
    Posts
    4,464

    Default

    We used Deoxidine (PA) when we were treating rust in vehicles. Worked extrembly well.

  15. #14
    Join Date
    Jan 2007
    Location
    Brisbane
    Posts
    696

    Default

    Must look into that

  16. #15
    Join Date
    Apr 2019
    Location
    NSW
    Age
    37
    Posts
    1,126

    Default

    and this is what a forstner bit looks like after you accidentally forget about it and leave it in ranex for 2 days.

    feels almost like charcoal or pumice. doesn't cut very well anymore either will push through but feels very spudgey. haven't yet tried to linish off that outer layer.

    20200723_073931.jpg

    20200723_073900.jpg

    20200723_073915.jpg

    20200723_073952.jpg

Page 1 of 2 12 LastLast

Similar Threads

  1. Rust Protection for Cast Iron
    By Mooncabbage in forum GENERAL & SMALL MACHINERY
    Replies: 5
    Last Post: 30th April 2015, 02:42 PM
  2. Rust Protection
    By Bobpol2 in forum TABLE SAWS & COMBINATIONS
    Replies: 8
    Last Post: 2nd March 2015, 09:39 AM
  3. The future of rust protection?
    By hiroller in forum HAND TOOLS - UNPOWERED
    Replies: 1
    Last Post: 30th January 2015, 05:31 PM
  4. How to remove rust protection
    By woodfast in forum METALWORK FORUM
    Replies: 2
    Last Post: 21st August 2014, 11:30 PM
  5. Rust removal Evapo-Rust
    By neksmerj in forum METALWORK FORUM
    Replies: 7
    Last Post: 22nd July 2012, 01:26 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •