Thread: G'day, newbie setting up...which router?

Welcome to the forum AyeJay. Opinions will vary on your router question. I use an old B&D for hand held routing but does not have a plunge action. My plunger router (hand held) is a Ryobi and it has served me well although I haven't used it that much over the years. I also have the big Triton but I don't think that would suit hand held routing to be honest. There is a smaller Triton but not sure if that is still available.
If you do a search on the forum, you will see lots of opinions and advice about routers. You may pick up some useful tips from reading those threads and posts.

Thanks for your reply munruben.

Can I ask how you use a router without a plunge action? Is this something that you have done (take out the springs) or do you have to wind it to the depth every time?

I have been reading quite a bit through these forums...most recommend the triton...but seems to me like triton is finished, so probably not smart to get one and then never have parts.

I should say that the ryobi I tried out had been sitting around for a few years, so perhaps I should just go cheap to start with.

(made my first trial mortise and tenon joint today...excellent!)

Welcome AyeJay
I hope you find the forum as useful as I do.
If your looking for a top quality router you can't go past a Casals. The model that will suit all your requirements is anFT2000VCE ½" Router 1900 W Variable Speed
I 've had one for a few months now and it has exceeded my expectations.
These are made in Spain and marketed in Europe and the USA under either Trend or Freud Brands. If you do an ebay search for Casals you can usually pick one up for about $250.00 and that's less than half the price you would pay retail.
Good luck with your search.

Welcome to the forum. I can not really answer your question on routers as I only have one and that is in the table. So far no need to take it out.

It is a Triton that I purchase before they went under and came back.

When I was at Carbatec Sydney last week, they claimed to (finally) have stock of the revised TRA001B (with the above table height winder a la MOF001). It looked like they were trying to shift the last couple of remaining original TRA001AU models before wheeling out the new stock?

For combination table/handheld use I prefer the smaller and lighter Triton MOF001, but the extra grunt of the TRA001 does come in handy if it is going to be permanently table-mounted.

Of course, if you want something more reliable with an assured supply of spares, it might be best to avoid Triton altogether . If the "rebirth" of Triton doesn't generate the level of sales Carbatec are expecting, then it might just be 'deja vu all over again' .......lol

Thanks SBoy for the suggestion...I will look it up.

So christos...when did the 'came back' part of triton's history take place??


mr Brush, what your saying is that carbatec is sort of running with the triton thing and hoping it works out?? hmmmm But yes, I agree with you...if things don't work out, I will have a tool with no parts supply....not so good.

I think late in 2009 they were back in business. But not in Australia, until early this year, when Carbatec announced that they have exclusive distribution.

I think this is pretty close.

Ayejay

I own the Makits 3612 single speed router. Great router and handles it all really well if your interested in looking at Makita. Only thing I wish it was varible speed. I know makita do the 3612C I think which is varible speed. Does cost a little more though.

I love the Dewalt 621 and reckon its the best router Ive used.....................Slap on a circular Sub-base N i reckon U got the Best Plunge Router for hand held use ever made!

I also have both Tritons; Top of the line Bosch and a huge Metabo I love the little Triton but the Dewalt 621 is the Router I always reach for.

Check out PAt Warners Router Website! its the definitive resource for all things router and does some excellent reviews of various makes n models....................well worth a look!

Regards Lou

Thanks Dave for your input...found the Makita 3612C for around 590...which is too much for me.

Lou, thanks for your input. I have actually thought about the dewalt quite a bit...I really like the way you can lock it by turning the handle and not having to reach for a lever. It is also cheaper by almost 200 dollars from the makita. One thing I have been a bit worried about though has been that it's only 1100W, which seems very very small.....what are your thoughts??

Another question is...where do you get this round base thingy?? or do you make one???

thanks guys.

Like all things its horses for courses...................n how effectively u use your tools

If your routers for home workshop use The 621's got more than enough grunt ..................If your doing production runs n pushing your router flat chat 4 hours a day then a more powerful unit is a necessity.

IF your going to be routing Via a Router table the majority of the time with occasional hand use its hard to beat the Tritons (Which are the ducks guts 4 underneath a table)

I'll just come clean upfront n let you know these things Breed like rabbits Ive got the luxory of using my 621 for HAndwork & Tritons for under the TAble.............

As a 1st Router the 621 comes from a great heritage & is hard to beat ink about what your needs are before you buy I know 4 me I did a lot more hand held work initially with my router But as u collect bits and get around to making a table new horizons and options develop.......................

A subbase can be bought or easily made yourself!!!

REgards Lou

thanks for the quick response Lou.

I really liked the weight factor of the 621 also by the way... The other options are bidding on Ebay for a small triton..or even a big one. I guess if I bought the 2400W triton I would get around to making a router table real quick!! haha

Can I ask if you made your sub-base, and if so..did you make one like the offset ones from pat?

Anyway, thanks SO much for your input, the list narrows a bit more!!

sorry...another question...have you ever found that the plunge depth on the 621 (53mm according to my research) has been limiting?

I made my 1st sub-base out of plexiglass from some off cuts from local industry ar-la PAt Warners design..........works a treat However its definitely not a necessity the 621 works fine as is!

If youve ever watched Woodworks hosted by David marks you'll see him almost exclusively using the 621 often with jigs; fixtures or a guidefence without any kind of subbase................So its definately not a must have addition to the mix.

HAve never found the 621's Plunge depth to be an issue N have used it under the table & also in my WoodRAt.................In my experience the plunge depth of the 621 becoming an issue would be quite rare!

Regards Lou