Thread: Jointing without a jointer

Great stuff Afro but credit goes to a bloke over the other side of the planet from FOG. I think it was Bob Marino.

Works a treat doesn’t it. Just remember to put the “good” side facing down so there is no tear out visible on the top.


[Edit- we had this in class today and Kelvin was their, I told him he should do the demo. Funny how you post it at the same time…. Spoooooky ]

Sorry to say that trick was around before Festo became a company, let alone made that saw. It is normally done with a router. Here's a sample from 2003. Fine Woodworking Magazine, October 1985 No. 54 also showed that technique with a circular saw. It sure wasn't anyone at the FOG dreamed it up.

Originally Posted by Groggy

Sorry to say that trick was around before Festo became a company, let alone made that saw. It is normally done with a router.

Funny thing, it’s been around for so long and nobody does it. Good on Afro for “jogging” everyone’s memory

Originally Posted by Lignum

Good on Afro for “jogging” everyone’s memory

Yep, a very handy technique.

Works on imperfect miters too. Many years ago, by Nawm (Abrams, New Yankee Workshop), with a hand saw or back saw.

Cheers,
Joe

Originally Posted by joe greiner

Works on imperfect miters too. Many years ago, by Nawm (Abrams, New Yankee Workshop), with a hand saw or back saw.

Good one. I never thought of using it for that. Will have to keep that in mind (perhaps with a hand saw though).

Now in the ,e,ory banks AB. Thanx!

I do jointing without a jointer using a different method.

I remove the normal fence from my router table and just have a straight cutter sticking up, then i clamp a really long straight edge to the table (the length must support the piece being machined as it travels all the way through the cutter from end to end). I then set the distance between the fence and the cutter as appropriate. You must begin machining your curved board on the convex surface (so it only cuts in the middle to begin with while the ends of the other side sit against the fence). Keep moving the fence inwards until you have one straight side. Then turn the timber around and do the other side so you are only cutting on the ends to begin with.

Hope that makes sense...i just finished machining up some black heart sassafras boards using this method and they came out great who needs a jointer anyway....just turn your router table into an edge thicknesser!!



Ash

Different method again. I glue the 2 boards together gaps and all. Then when they are dry I run the table saw down the joint. If the kerf isnt enough the first time its usually ok the next time. If you use a fine toothed blade it usually gives the perfect surface for glue.

Ash, are you running the workpiece between the cutting bit and the fence?

Originally Posted by Groggy

Ash, are you running the workpiece between the cutting bit and the fence?

Yes Groggy thats right....being very careful along the way.

I guess you know the risk Ash, but for the benefit of any newbies to routing, this is not a practice for the inexperienced or faint of heart.

If feeding with the cutter (climb cut) the router can pull the workpiece and fire it like a missile across the room, or, if feeding against the cutter it can pull the workpiece across the cutter and destroy the workpiece.

Experienced users may do it but have a good think about where the timber is aiming before you try it. Never try this with the body in the firing line. Strong fingerboards are highly recommended to keep the work pushed against the fence.

Originally Posted by Groggy

I guess you know the risk Ash, but for the benefit of any newbies to routing, this is not a practice for the inexperienced or faint of heart.
.

Spot on Groggy. Could be very scary for a newbie (scary for me as i hate routers full stop )

Originally Posted by ash233

Yes Groggy thats right....being very careful along the way.

Mate, that's something I would never do. Sorry!