Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: crane mount
-
24th June 2009, 11:52 PM #1
crane mount
I'm sure most of us have seen ute cranes on trailers before. Figured I would have a crack at making a mount for one whilst giving the trailer a paint up.
So here is what I came up with. Top is 8mm plate with a 5 mm angle extension. Extension actually goes outside the guards, figured this might pushing the rules a bit, so I made it so it could detach with the crane base. Under the trailer I have welded a couple of 75 x 50 mm between the "ribs" and ran 50 x 50 mm between them to form the base of the mount. The uprights are 5 mm angle to support the top.
I put the whole show to the test recently when I removed a heap of garden rocks and a rather stubborn fence post. Once I find a suitable wind down leg I will attach it beneith the trailer as the suspension sagged somewhat when pulling out the post.
When I bought the trailer it a was a very basic affair. No carrier for the spare of tie offs above the guards. Over time I have added these on as well as making detachable tradie bars. Currently making ramps, more pics of these to follow once I get my act together and take some.www.lockwoodcanvas.com.au
I will never be the person who has everything, not when someone keeps inventing so much cool new stuff to buy.
From an early age my father taught me to wear welding gloves . "Its not to protect your hands son, its to put out the fire when u set yourself alight".
-
24th June 2009 11:52 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
25th June 2009, 09:43 PM #2
A flip-down strut, similar to a bicycle kick stand, might be simpler than the wind-down leg. It could be about 25mm shy of "perfect," to accommodate varying terrain, and still reduce trailer sag. It looks like you have enough room to drill holes for the axle and locking pins, without removing the rig from the trailer frame.
Very nice work, BTW.
Cheers,
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
26th June 2009, 12:38 AM #3
Nice one Jatt.
Does the crane itself swivel?
Also, a piece of SHS welded upright to the outside of that L/H rear light box, with another tube sliding up & down inside it, with either a pin arrangement (like a jack stand) or a "T" handle made up from a bolt and a piece of rod welded across its head and a nut welded to the outside tube giving you a clamp arrangement for height adjustability, would stop the trailer sagging under load.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
26th June 2009, 07:26 PM #4
Yep the crane swivels. Its just one of those off the shelf units one buys with a bottle jack to push up the crane boom. Simply sits in the base and employs a bearing to provide azimuth (horizonal rotation).
Some interesting ideas for me to ponder wrt to a drop down leg.www.lockwoodcanvas.com.au
I will never be the person who has everything, not when someone keeps inventing so much cool new stuff to buy.
From an early age my father taught me to wear welding gloves . "Its not to protect your hands son, its to put out the fire when u set yourself alight".
Similar Threads
-
Crane truck
By Chooks74 in forum SMALL TIMBER MILLINGReplies: 3Last Post: 22nd October 2008, 01:15 PM -
Toy crane
By Andy Mac in forum WOODWORK PICSReplies: 5Last Post: 15th October 2007, 12:51 AM -
Toy crane
By RichardL in forum WOODWORK PICSReplies: 6Last Post: 15th February 2006, 02:09 PM -
Snadhill Crane.
By Bob H in forum INTARSIAReplies: 6Last Post: 26th April 2005, 12:08 PM -
Boice Crane
By Jeff in forum BANDSAWSReplies: 0Last Post: 12th September 2003, 02:15 PM