Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Replacing springs?
-
23rd October 2013, 02:34 PM #1Senior Member
- Join Date
- Sep 2008
- Location
- Perth
- Posts
- 363
Replacing springs?
Putting the rear slipper hangers in today - but I thought there should be provision for replacement if they ever break? With the springs/hangers I have, the only way you'll get the old ones out is if you cut off the end. It hangs down at a right angle. And if the new replacements are the same type, they'll never be going in. Is that right?
-
23rd October 2013 02:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
29th October 2013, 11:25 PM #2
Huh..?? Do you mean replacement hangers, or replacement springs?
Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
30th October 2013, 09:39 AM #3Senior Member
- Join Date
- Nov 2008
- Location
- Qld. Australia
- Posts
- 417
Maybe has springs like these -
https://www.etrailer.com/Trailer-Sus...ine/803T3.html
Nev.
-
30th October 2013, 11:51 AM #4Senior Member
- Join Date
- Sep 2008
- Location
- Perth
- Posts
- 363
It's done now. I mean if the springs break and I need to replace them, I can't without cutting off the hangers. I have springs just like the ones Nev linked, with a right angle "keeper" at the back, which means I can't slip them out. Oh well, if I ever break a spring it will make field repairs slightly more difficult.
My question was if there was a trick to it that I was missing, because I was considering welding in gussets to the hangers a bit like I welded the drawbar to the front hangers a la Yonnee's tips. But considering there is no load on the rear hangers and I did three passes on each side, strength isn't an issue and no gussets makes removal easier.
-
30th October 2013, 03:31 PM #5Senior Member
- Join Date
- Nov 2008
- Location
- Qld. Australia
- Posts
- 417
Just guessing here but they look like they would come out of rear hanger if they were unbolted from front and dropped down and slid forward.
Nev.
-
30th October 2013, 03:47 PM #6Senior Member
- Join Date
- Sep 2008
- Location
- Perth
- Posts
- 363
No, it's too tight. You'd have to either cut off the hangers (if replacing with the same springs) or cut off the right-angle bit if the replacement springs were flat slippers and could fit in. Just a bit of insurance I guess, to stop them falling out when you back over a bump.
-
14th November 2013, 08:09 AM #7Senior Member
- Join Date
- Dec 2011
- Location
- Deception Bay Qld
- Posts
- 213
Hi Legion, Some trucks in the 50's to 70's used the same type of spring, the cast hanger was open at the bottom with a bolt and sometimes a piece of pipe as a roller to capture the spring. This post might be a bit late as I don't visit this section to often.
Similar Threads
-
Slipper springs .. does this look right ?
By kenny_10 in forum TRAILERS & OTHER FABRICATED STUFFReplies: 3Last Post: 31st March 2013, 10:19 AM -
Are my springs ok?
By tasgc in forum UPHOLSTERYReplies: 1Last Post: 30th May 2012, 11:08 PM -
Making own springs
By WA Pete in forum METALWORK FORUMReplies: 5Last Post: 12th May 2011, 12:13 AM -
Trailer springs
By Tigershark in forum TRAILERS & OTHER FABRICATED STUFFReplies: 2Last Post: 25th February 2010, 03:23 PM -
Trouble with springs
By Tiger in forum HAND TOOLS - POWEREDReplies: 6Last Post: 11th October 2005, 12:21 PM