Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 16
Thread: 2 new tables
-
27th April 2010, 12:09 AM #1
2 new tables
Here are my last 2 projects:
1) Spotted Gum hall table - 1000L x 400W x 800H. Finished with several coats of Danish Oil
2) Blackbutt coffee table - 1000L x 600W x 450H. Again finished with several coats of Danish Oil
All joints are loose tenons.
I experimented a bit on the blackbutt table both with design and construction method. The timber I used was all 90 x 18mm, and I wanted 90mm square legs. I didn't want to see the lamination of the legs so for each leg I mitred the edges of 4 pieces and glued them together. It was a bit of mucking around but I think it worked out well. I then had to make up something to cover the top of the legs.
The design I'm still not sure about. Be brutally honest and tell me what you think - It'll help me with future projects. (Please excuse the blue carpet mat - SWMBO likes it)
-
27th April 2010 12:09 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th April 2010, 12:39 AM #2
Hi Kev, you have been making use of that Blackbutt. Your side table looks great and your finish was fantastic, I'm not overly keen on the drawer pull but thats a personal tast thing. I like them a little plainer. Your coffee table is an interesting piece, wow, mitred legs, I haven't come across that before, a lot of work. Once again I like things a little plainer and would have just run the top over the legs but again thats just my taste. For everyone that likes it plainer you will find someone who likes more detail as you have done. Great pieces Kev and you have lots more Blackbutt to go mate.
-
27th April 2010, 01:52 AM #3
Outstanding work Kev. I really like the slim elegant lines of the hall table. And I can't imagine how hard it was to make the mitred legs.
-
27th April 2010, 04:29 AM #4
Spotted gum is so under rated, you have used some nice pieces and the finish is natural. You are making some individual pieces, stick with what you like to do and don't stray back to the "norm"
Dills.
-
27th April 2010, 07:32 AM #5Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Beautifully made and finished Kev.
I particularly like the Spotted Gum used in your hall table.
-
27th April 2010, 08:43 AM #6
I like the hall table, the way that you used one piece for the front and draw.
The way that you did the coffee table legs in interesting and some very long hours I figure. For me and only for me I would prefer to have the top flush with the top of the legs. Keeping the top design of the legs as what you have done. Almost like at insert or patch.
-
27th April 2010, 12:32 PM #7
Kev,
The hall table is first rate and a very nice bit of spotted gum too.
I can imagine the work in mitering the legs and would have left the tops uncapped to feature the mitering. The end grain would polish up well and show you had put a lot of work into it. Like the rest I am not a fan of the legs being raised above the top that far but then personal taste has a very wide range.
Good work.
Regards
John
-
27th April 2010, 06:53 PM #8
Look good, well done
Have a good one
Keith
-
28th April 2010, 06:02 PM #9
Thanks for the comments.
Yeah, although the coffee table looks a little better in real life than the photos I wasn't convinced I chose the best design. I don't think I'll do it again, although the leg tops are perfect for putting coffee cups on
The mitred legs weren't really a huge amount of work. I sized all the timber to the same thickness, set the table saw to 45deg and ripped the pieces through. The glue-up was just like a box - I placed the pieces side by side on a couple strips of strong sticky tape, applied glue and rolled it up. Then applied more tape and squeezed it as tight as possible. Because the angles were right they all fitted together nicely.
I then glued a piece of timber inside where the mortises were going to provide more glueing area and support for the joint.
Kev
-
28th April 2010, 06:18 PM #10
Sounds good Kev and a great job, the tops of the legs look great too, just they are up in the air. It does look good we are only nit picking realy
-
28th April 2010, 06:26 PM #11
Looks great!!
-
27th June 2010, 12:34 AM #12Intermediate Member
- Join Date
- Jun 2010
- Location
- Adelaide
- Posts
- 25
kev i really like your hall table ....just wondering what your method was to get your drawer front from the front rail??? cheers mate
-
27th June 2010, 11:36 AM #13Senior Member
- Join Date
- Apr 2009
- Location
- lismore nsw
- Posts
- 116
Great work ,some unusual design features there , but i like them ,shows individuality of thought and design , good one
-
28th June 2010, 11:44 AM #14
Thanks again for the comments.
The drawer front was made by cutting the timber into 5 pieces as per diagram. Depending on the desired gap around the drawer cut a bit more off the top and/or bottom edges of the drawer face. I have a 1.5mm gap so I cut that amount off the top and bottom.
Then glue pieces 1,2,3 and 4 back together leaving a 1.5mm gap on the sides of the drawer face.
-
28th June 2010, 09:35 PM #15Intermediate Member
- Join Date
- Jun 2010
- Location
- Adelaide
- Posts
- 25
oh lovely! i havent done it like that before but had actually heard about the way you;ve done it was curious to know for sure tho! looks damn good....all the coffee or hall tables i make at work, they have a drawer front screwed to the front of the drawer and i cut it out of the same piece i get the side rails from so it somewhat looks like a continual piece at first glance, but your way is a ripper ...will do it like that next time i get a halltable job at home
cheers for the clarification!
and once again, top tables!
Similar Threads
-
Vacuum Tables
By twistedfuse in forum CNC MachinesReplies: 0Last Post: 4th August 2008, 02:16 PM -
End tables WIP
By Andy Mac in forum WOODWORK PICSReplies: 26Last Post: 8th September 2007, 05:59 PM -
Router Tables
By echnidna in forum ROUTING FORUMReplies: 10Last Post: 13th July 2006, 11:07 PM -
Tables
By John Saxton in forum Links to: WEB SITESReplies: 2Last Post: 1st January 2006, 03:00 PM -
Tables
By pomjohn in forum ROUTING FORUMReplies: 4Last Post: 10th July 2002, 02:32 PM