Results 1 to 3 of 3

Thread: Beds revisited

  1. #1
    Join Date
    Apr 2001
    Location
    Perth
    Posts
    10,810

    Default Beds revisited

    See my previous post, "Morticing the easy way", by way of introduction.

    This weekend I rebuilt two single beds (they had been completed some weeks back). It was a lot of work. Basically, I had screwed up by oversizing the beds 40mm in length and 40mm in width.


    To correct this, the beds were taken apart, and the rails shortened. Then the head- and foot boards were shortened, re-morticed, and re-glued. And finally, all the slats had to be shortened by 40mm, which was not a simple matter. More on this in a while.


    About the beds and their design: One of the reasons I am posting the build details is that I hope it helps others in a similar position.


    About 25 years ago I build a fantastic Jarrah King size double bed for my wife and myself. It was deliberately built 25mm over-width (which made it appear even wider) ...







    The reason for this is my wife is an incredibly light sleeper, especially since our son was born 3 decades ago, and will wake up if I even roll over in bed. We spent a small fortune on mattresses ... all those special ones which promised to smother any vibration. Well, all I can say is that I am lucky I was not smothered in my sleep! The solution for a while was the King size bed with two single mattresses, pushed together, but able to be pulled apart by 25mm if I was restless in sleep. The issue with a single bed is that vibration is transmitted by the bed frame. Consequently, I decided to build two beds which would actually become a double bed, but able to be separated if needed. I will explain this in a while.

    As mentioned, these beds are done. Now I have a new headboard to build, which is for another time.

    My wife stipulated no tail board for the beds as they make is far more work when making up a bed. My preference was for clean lines, which meant that I did not want visible bed bolts. Bed bolts are used, but they are hidden.

    Here is the start of re-assembling the beds ..









    The head and tail ends are constructed with a mortice-and-tenon (this was the post made recently on morticing with a Domino). The side railed are connected with hidden bed bolts.

    Here are the side rail connections. When the rails were shortened, so the bolts in these rails needed to be ..







    The bolts are fixed into inserted metal threads in the posts permanently with Loctite. The post and rail are locked with double loose mortice-and-tenons (no glue) and then bolted in the rail ...







    The slats for the beds are made in two parts ...







    They are a T-section, which makes for a very rigid structure ...







    ... and screwed down for extra strength.


    Now the secret to making a double bed out of two singles lies with the rails. The slats on the outer sides are lower by 6mm (1/4") to aid in preventing the mattress slipping off the base, but also low enough to make it easier to tuck in sheets, etc.






    The slats on the inside rails are flush with the top ...






    ... enabling two mattresses to be placed alongside one another. Conversely, it is easy to pull them apart.


    The Jarrah is finished in hard wax oil, and the result is quite stunning. Difficult to see in this light ..











    Now I am left with the headboard to make, which will be secured to the wall and not the beds. The wood will come from these ...







    Laminations and curves are planned.


    Regards from Perth


    Derek
    Visit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Nov 2004
    Location
    Redlands area, Brisbane
    Posts
    1,489

    Post

    I made the opposite mistake on the bed I made for us. It is a fraction too close a fit for a queen size mattress ensemble. It makes changing bed clothes far harder than it should be. Especially with hands that are not getting better with age!

    As mistakes go on a bed frame, too long is not a major problem. There are custom mattress manufacturers around and they are not stupidly priced.

    I'm going to make an extension to the rails that will sit over the ends of the rails. Or I might just get a new mattress ensemble made to suit. We are probably due for a new one anyway.

  4. #3
    Join Date
    Apr 2001
    Location
    Perth
    Posts
    10,810

    Default

    I hate making (not building) beds, even one as simple as ours (sheets and doona), so Lynndy does them. She reports that it is now super-easy. I appear to managed to get the dimensions just right this time. Whew!

    Meanwhile, I cannot believe how heavy the old head board was! It required bother of us to carry it to the workshop, and I struggled even though I positioned Lynndy in its centre ...

    Regards from Perth

    Derek
    Visit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.

Similar Threads

  1. Exhaust Fan Revisited
    By bitingmidge in forum DUST EXTRACTION
    Replies: 3
    Last Post: 19th March 2021, 10:49 PM
  2. A Pen Revisited
    By Ironwood in forum WOODTURNING - PEN TURNING
    Replies: 5
    Last Post: 16th September 2014, 09:08 PM
  3. CEO revisited ?
    By gawdelpus in forum WOODTURNING - PEN TURNING
    Replies: 2
    Last Post: 19th November 2011, 10:03 PM
  4. Bed To End All Beds
    By Corcorbear in forum WOODWORK PICS
    Replies: 19
    Last Post: 15th December 2005, 01:50 AM
  5. day beds
    By nakia in forum WOODWORK - GENERAL
    Replies: 2
    Last Post: 5th May 2004, 09:00 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •