Results 1 to 15 of 109
Thread: A Coffee Table With A Twist
-
29th October 2022, 11:30 AM #1
A Coffee Table With A Twist
Back in England I remember my parents having an antique card table, I think it was french in origin due to
fleur-de-lis pattern on the legs. As a child I was fascinate by how it pivoted and opened up to this grand playing area. I thought it was great because I could hide my action men in the recessed area!.
The mechanics for this design are based on my parents table but obviously as a coffee table rather than a full sized side table. I'm hoping that I might get some help from you fine people with the construction.
One of my concerns is the back of the table where the three draws are. The table top will be made from plywood and solid timber but I'm worried that 12mm plywood might warp when the table is in the closed position. The 12mm plywood would span aprox 1120mm without support. The three drawers on the rear incidentally are accessory trays for attaching to the side of the table when its in the open position. But for now I just want to get the table design structurally correct.
Help and constructive criticism most appreciated!.
Untitled-1.jpg Untitled-2.jpg Untitled-3.jpg Untitled-4.jpg
-
29th October 2022 11:30 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
30th October 2022, 07:28 PM #2
The accessory trays simply slip into the void left when the table is closed?
If so - and they're a snug fit - they should stop the top piece from sagging. Not an ideal situation for several reasons, including wear 'n tear on the upper/lower surfaces of the trays, but they should stop any sagging so long as they're replaced religiously when the table is closed.
It'd be an interesting exercise if you're planning on lining the 'inner' table and don't want the edges of the liner to show above & below the accessory trays, but that's still quite do-able. More than anything, I'm curious as to how you intend to stop the trays from being inserted too far.
Of course, I could easily be reading things wrong.
- Andy Mc
-
30th October 2022, 07:48 PM #3
Your're spot on with all the points you've made. These are issues I need to find a solution to so I really appreciate your post. One thing I was thinking of with the trays was the use of magnets to hold the trays in place... As for the lining showing, there will be a solid timber edging strip aprox 17 x 90mm on upper and lower leaf. I'll post some more photo's after I've let my dinner go down to give a clearer picture of the accessory trays etc.
-
30th October 2022, 09:08 PM #4
So I've added a mitered edge to the back side of the table top to add more rigidity and increased the thickness from
12mm to 17mm.
Untitled-5.jpg Untitled-6.jpg
Here are some examples of the types of accessory trays, theres hundreds you could probably make.
utrdjq5a.jpg
-
30th October 2022, 09:12 PM #5
According to Sagulator I should get very little sag or deflection with 20kg on top of the closed table position.
-
12th December 2022, 07:26 PM #6
I started by making the four legs which will become part of the side panels. The core is hevea timber laminated with 5mm Oak to make them hopefully look like solid oak legs.
IMG_9089.jpg IMG_9118.jpg IMG_9119.jpg
Next I did the joinery.
IMG_9127.jpg IMG_9126.jpg
Done, side's finished. Well, apart from the beading and fancy bits which will be done later.
IMG_9128.jpg
-
12th December 2022, 08:13 PM #7
I forgot to show a close up of the joinery:
IMG_9131.jpg
-
15th December 2022, 03:08 PM #8
I consider myself very much a beginner especially compared to some of you fine folks so If I've made any mistakes or there is an easier way of doing something that you can see, design or otherwise I'd really appreciate your help and constructive criticism as its the only way I'm going to learn and progress.
I hope you all have a great Xmas guys.
-
15th October 2023, 05:41 PM #9
Continuation Finally!
So having finally built a workbench/assembly table and after returning from England I set about continuing this project of mine. Firstly I wanted to change a few design aspects of the coffee table. I didn't really like the idea of the shelf so I decided to make a further four drawers above the two larger ones at the bottom. This gives the ability to store small game accessories like dice & cards.
00rededign.jpg
With the change of design in my minds eye I set about gluing some plywood together to level out the inside panels.I used my vac press for this job but as you you can see i didnt give enough room between the panels to stay flat so I ended up with one lifting up like a crane! (fool!):
01Glue Up inside Panels.jpg
Once they were glued all I needed to do was cut them to shape and glue them to the side panels, my new vice came in very handy for one of the glue ups:
02Glue up Side Panels.jpg
Next was making the frame & pane back. Joinery was just basic mortise & tenon.
04aIMG_0008IMG_E008.jpg
The top and bottom shelves were made next, slightly oversized so I could cut them to size upon fitting. Just screw & glue joinery here.
05aTop Tray.jpg
Next I made a dividing wall out of plywood then I tongue & grooved the end with white oak as that's what will be on display. This will be held in by dowels:
05IMG_0012.jpg 06aaIMG_03.jpg
Once I assembled it all I soon realised I had made a mistake, rectifiable fortunately!, The dividing wall was cut to the height of the sides, it needed to be cut to size as to allow the top shelf!. Luckily I hadn't glued the dowels at this stage so it was just a matter of pulling the thing out.
06IMG_0014.jpg
Rectified!:
08IMG_0015.jpg
This is where I feel I should have planned ahead a little better as I soon realised fitting the two shelf drawer dividers was not going to be easy due to lack of drilling access. Despite this I managed to come up with a solution and fitted the shelves by drilling the dividers outside of the carcass and screwing them in after:
09IMG_00212.jpg, 10IMG_0024.jpg
The top shelf was test fitted next. No issues there everything was nice and square. This will eventually be doweled in place but at this stage its better to leave until other things have been done beforehand.
11IMG_0023.jpg
At this stage because of weight and mobility I decided to install some very nice antique brass casters, I got them off Amazon for for about $40. Molding will eventually conceal these but I will leave access to them as per the design.
12amRqeL._SL1500_.jpg 12IMG_0027e.jpg
-
15th October 2023, 05:48 PM #10
Next post will be making the panel molding.
-
15th October 2023, 07:32 PM #11GOLD MEMBER
- Join Date
- May 2011
- Location
- Albury
- Posts
- 3,030
Making that bench and the workshop drawers must have given you so much additional confidence when tackling a bit of 'inside' furniture. It's loooking very nice.
-
15th October 2023, 08:50 PM #12
-
15th October 2023, 08:57 PM #13
Because this will be house furniture I wont be using store brought drawer runners, I'll be asking forum members on a traditional way of making them run freely. As for the joinery I'll be using box joints.
-
16th October 2023, 07:57 AM #14SENIOR MEMBER
- Join Date
- Feb 2018
- Location
- Shepparton
- Posts
- 510
Traditionally the way to do runners was coat them in candle wax to help slide and occasionally top the up with wax.[early with this advice but couldn't help myself]
-
16th October 2023, 12:26 PM #15
Having milled some more white oak I set about making some molding for the outside panels. I used a classical ogee router bit and went back and forth from the tablesaw & router until I had enough to do all
three sides of the carcass, actually I did a little too much!.
14IMG_0034.jpg 15IMG_0035.jpg 16IMG_0036.jpg
I've been meaning to buy myself a 23 gauge Pin Nailer for a while now, I opted for the Makita brand which is expensive for what it is but will be worth it in the long run:
17IMG_0043.jpg
Onto cutting the Mitres now. This is where my cross cut sled really came into its own, it made the process very easy indeed, accuracy with this thing is superb cutting all mitre joints perfectly!, I'm so glad I made the sled the way I did because I can mitre both ends of the molding without touching any setup:
18IMG_0046.jpg 19.jpg
With everything test fitted I finally glued and pinned the molding into place. The first one I used too much glue with the first one and I had abit of cleaning up to do which left one of the panels with some sort of stain. Not to worry though as the whole thing is going to be stained a dark colour anyway:
20MG_E0048.jpg, 21IMG_E0049.jpg
Similar Threads
-
Barley twist table
By Blackout in forum RESTORATIONReplies: 0Last Post: 7th September 2019, 06:49 PM -
Side table with a twist
By Kuffy in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 10Last Post: 12th May 2017, 04:23 PM -
Twist in table top boards
By Acer in forum WOODWORK - GENERALReplies: 4Last Post: 2nd October 2011, 10:53 PM -
Wanting to Buy - 2xTV unit, Coffee Table Dinnng room table
By Overboardkiller in forum WOODWORK - GENERALReplies: 6Last Post: 10th November 2010, 05:59 PM -
Tall Coffee Table/Desk/BookCase/Holdall of important bits/Sofa Table
By RufflyRustic in forum WOODWORK PICSReplies: 11Last Post: 3rd December 2009, 12:14 AM