Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
16th December 2011, 04:12 PM #1New Member
- Join Date
- Dec 2011
- Location
- Humpty Doo, NT
- Posts
- 2
Best finish for recycled timber table
Hi all, I'm new to this forum and as my user name suggests I'm a bit of a DIY hack, not that I'm entirely hopeless more that I'll just have a crack at anything using the trial and error method.
Recently I picked up some old furry joists to make into an outdoor table. I had enough to make the top out of Jarrah and the base out of a lighter timber with an old shipping stamp from Malaysia, maybe Merbou??. Thankfully a mate had a thicknesser and a table saw so we were able to clean them up pretty well although they are still a little warped. With this in mind and knowing my limitations, I've decided to go for the rough and rustic look which has come up not too bad for my first attempt at woodwork since high school.
As is my usual style I rushed into giving it a coat of Linseed oil (the aniti-mould stuff from Bunnings) after sanding and before assembling without doing much research into the best oil to use. WAS THIS A BAD MOVE???
I have only done one coat and it's not too bad but I was hoping for a slightly harder and glossier finish.
Can I use a wax over the top to fill some flaws? or am I locked into using Linseed oil for ever now?
I would much appreciate if some of you seasoned woodworkers out there could give me some advice, bearing in mind I live in Darwin where the temperature and humidity is rather extreme for a lot of the year.
Couple of photo's attached of the unfinished product.
Attachment 191247
Attachment 191248
Attachment 191249
-
16th December 2011 04:12 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th December 2011, 07:18 PM #2
Hi DH and welcome to the forum. When you say outside is it under cover or outside in the sun and rain?? If its under cover I would use some more boiled linseed and build up a few coats until you get a nice sheen. If its out in the weather I would give it another coat of linseed for now but in 3 months when it needs it next coat I would just go an oil base deck oil (Cabots). In all cases rub in the oil leave it for 30 min or so and then rub it off. If you leave it too long it will get tackie and become very hard work. Good luck.
-
16th December 2011, 09:26 PM #3New Member
- Join Date
- Dec 2011
- Location
- Humpty Doo, NT
- Posts
- 2
Thanks Claw Hama,
Table will be outside but under cover. Any advice on the wax as there are a few natural knot holes and some protruding nail holes that are a bit flakey and no doubt with time will trap food and stuff in them?
-
16th December 2011, 10:25 PM #4
Yep if under cover some Canuba wax maybe the go (harder/tougher I think). I also think it has a higher melting temp too which could be good for Darwin temps. With wax comes rings though. If you put hot cups etc you may get rings. You could just limit it to the holes etc rather than going all over it.
Similar Threads
-
Recycled/reclaimed timber dining table WIP
By Claw Hama in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 90Last Post: 16th June 2011, 08:51 PM -
IronBark recycled timber bed - Wax finish advice needed please
By 80nus in forum FINISHINGReplies: 0Last Post: 19th April 2011, 01:28 AM -
recycled timber for table
By redgreg in forum TIMBERReplies: 3Last Post: 3rd June 2010, 09:45 PM -
WIP - Chunky cottage coffee table (recycled pallet timber)
By Robomanic in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 14Last Post: 15th March 2009, 10:59 AM -
how to clear-finish a Recycled 1885 Oregon ?
By Vero in forum FINISHINGReplies: 7Last Post: 27th May 2006, 12:48 AM