Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
-
28th July 2012, 12:53 AM #1
Nagashima style ironbark crotch table WIP
You know how one thing leads to another, with the router flattening gadget up and going I flattened the 4 other slabs I had, I had a look at some of George Nagashima's work and I think these slabs will work in that style, not sure if I'll do it justce but will give it a go.....
At this point I am thinking of a few variations on a theme, we'll see....
One of the forked slabs I will use as a leg
Attachment 217309
I had one slab that had some bad splits so I cut them out and then reglued, not easy stuff to handplane when prepping the join Had to put a clamp lengthways to stop them sliding , even with a dry clampup seems that the glueup behaves different with a bit of glue in the join
Attachment 217307Attachment 217308
I chalk marked some parts (rails/legs) on a slab prior to ripping
Attachment 217310
Pete
-
28th July 2012 12:53 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
28th July 2012, 12:09 PM #2
This looks interesting, I'm watching.
The time we enjoy wasting is not wasted time.
-
28th July 2012, 01:09 PM #3Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Watching!
-
30th July 2012, 01:12 AM #4
Legs and things
Cracks to be filled in the tops and parts cut from the slab it was dressing and thickness sanding to final sizes, then there's lots of umm and arring about how to get what's in my head to a tangable object, compound angles to cut so only get one chance so go gentle with the cutting and make sure I do right and left hand cuts mark out a bit of a full size plan on the melamine table and go from there.
With the legs cut to length, next is what will be the halved joints at the btm of the legs, I need to be able to hold them at the 9° angle, I had a jig made up to hold wide boards upright on the TS so I modified that by adding some bits of pine to it,
Attachment 217589
I didn't think about the grain direction until I came to screw the chipboard onto the bits of pine ohhh end grain into pine, oh well it's only a quick jig, it'll be right says he to himself, nope, as soon as the countersink hit the chipboard that was itok fix that with some dowels
Attachment 217590
I am keeping most of the natural edge so an edge stop is not an option, I added a flip stop to the top of the jig to give me my two faces of the joint, I clamp a block to the leg once I have located one face of the joint
Attachment 217591Attachment 217592
and a bit of a throw together to see what it will look like
Attachment 217593Attachment 217594Attachment 217595
I think the general arrangement will be OK
Pete
-
31st July 2012, 12:49 AM #5
I cut the narrow leg half joint today plus the half joint in the rails very carefully just so easy to cut something at the wrong angle, I also installed an additional DE line for overhead use on the TS,
just a couple of pics today, I use a spacer to set the width of the joint
Attachment 217736Attachment 217735
Pete
-
23rd September 2012, 05:22 PM #6
Tables finished
Hi all,
I have had these small tables finished for a while now but just keep getting side tracked with other things and have been slack in getting back to load the pics, I would load more pics but pic attaching is a pain atm, so just a few until I workout the new system....
I decided on spaced cross pieces to form a low shelf using another half depth joint, I cut these joints out using the backsaw and a wooden block clamped to the rail for a guide, ( I wobble too much otherwise), sometimes it's easier to do things by hand rather than set up a machine, I also made a jig to run along the spindle moulder to shape some small feet, I also made a position adjuster for use with the router for when I want to increase the width of a slot or tweaking the position of the slot
cutting the notches in the low rails.JPGlow rail on jig.JPGjig for shaping feet on low rails.JPGposition adjuster.JPG
-
26th September 2012, 09:42 PM #7
I think you have worked out how to post the photos.
There was one that did not come up ok. Might not have fully loaded.
Thank you for the update.
-
27th September 2012, 09:29 AM #8
I like the grain in the timber Pete, will be great to see the end product, looking good
-
28th September 2012, 01:25 AM #9
The finished tables
Three different tables but similliar in the style....
fork table 1.JPGFork table.JPGfork table end.JPGErosion table.JPGErosion table top.JPGLadder table1.JPGLadder table 1.JPGladder table top.JPG
Not sure which one I like best, I like where both forks meet, the carved ends on the erosion, the finish on the ladder
Pete
-
28th September 2012, 07:23 AM #10
Great work Pete, they've come up really well. Each one has it's own feature, I like how the top and leg crotch meet, but I think my favorite is the one with ladder legs, they're just right, to my eye at least.
The time we enjoy wasting is not wasted time.
-
2nd October 2012, 11:08 AM #11
I tending toward the one on picture number four.
-
2nd October 2012, 05:33 PM #12Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Well Pete, I would hate to be forced to choose! they are all excellent tables!!
-
2nd October 2012, 07:34 PM #13
Great job Pete! I kinda lean towards the eroded end - I think in the flesh it would have great appeal.
Similar Threads
-
Small Ironbark crotch table
By pjt in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 5Last Post: 22nd July 2012, 08:30 AM -
Grey Ironbark dining table WIP
By Claw Hama in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 102Last Post: 19th January 2011, 12:05 AM -
Chinese Style Table
By roland in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 10Last Post: 1st January 2011, 10:34 PM -
Red Ironbark Slab Table WIP.
By Eldanos of KDM in forum WOODWORK PICSReplies: 21Last Post: 20th November 2009, 08:40 PM -
shellac/danish oil/tung oil/wax on ironbark dining table
By Sweevo in forum FINISHINGReplies: 15Last Post: 28th October 2009, 11:51 AM