Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Outdoor Kitchen
-
2nd September 2012, 10:20 PM #1Member
- Join Date
- Mar 2012
- Location
- Adelaide
- Posts
- 54
Outdoor Kitchen
Hi Everybody,
The forum here has given me great advice over the years but this is my first post.
I am building an outdoor kitchen with sink, gas cooktop (mate upgraded his), built in 4-burner bbq and build in charcoal grill. The plan is to build a wooden frame top with hardieflex and then tile on top. Within the frame will be a number of drawers and the sides will be clad with a decking timber of some kind (TBD).
My question is to do with the built in bbq's. I was going to build a wooden frame with a suitable opening for the bbq and encase with hardieflex on all sides to give me a fireproof box to house the built in bbq. Does anybody have any experience with this, is hardieflex an appropriate material or should I be using something else? Also, I was considering painting the hardieflex box although I could tile, any thoughts?
Any advice you can give me would be much appreciated.
Cheers...
-
2nd September 2012 10:20 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd September 2012, 12:07 PM #2SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Is your outdoor kitchen under cover or exposed to the weather,the reason I ask is that I made a unit that was outside and put cement sheet on the top surfaces,sealed it then tiled thinking it would be water proof,not a good plan had to rip all off and start again.
I have a mate who is in the stone business so got stone tops at mate's rates.
The sides are made of treated ply sheets,I think it's call Shadow Line,this I then painted it.
Been done for a couple of years now and still looks good.
-
3rd September 2012, 08:41 PM #3Member
- Join Date
- Mar 2012
- Location
- Adelaide
- Posts
- 54
Thanks for the reply nrb The pergola is covered and the kitchen will be situated in one corner that will be enclosed by the wall of the house and a blueboard wall. One side will be open but possibly have a bistro blind down the track.
So I'm guessing that tiles covering cement board should be appropriate as the area should get very little if any water. Do you think a painted cement board covering a wooden frame will be sufficient for housing the bbq's within the kitchen?
-
3rd September 2012, 08:48 PM #4SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
That should be fine,best of luck with your project
-
3rd September 2012, 08:49 PM #5Member
- Join Date
- Mar 2012
- Location
- Adelaide
- Posts
- 54
Thanks mate, I'll post some photos when its eventually done!
Still got to pave first!
-
25th October 2012, 11:48 PM #6Member
- Join Date
- Mar 2012
- Location
- Adelaide
- Posts
- 54
I am finally getting started with this project!
Just wondering, I am putting up some half walls around the pergola between the posts and using harditex. My plan was to route a groove into a timber frame and sit the harditex in the groove so it is fully enclosed and surrounded with the framing timber and then paint. I think this will give a nicer finish than just cladding the frame with the harditex and then having to do something with the edges and having to seal joints etc. Does anybody see any problems with this approach? Is blueboard commonly recessed into timber slots or is it more commonly attached to framing and rendered etc? I was then simply going to fill any residual gap and paint without rendering...
Similar Threads
-
Year 12 major work - Outdoor kitchen unit
By azza94 in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 21Last Post: 24th August 2012, 08:28 PM -
another outdoor piece
By Corgan in forum METALWORK FORUMReplies: 5Last Post: 3rd September 2011, 06:56 PM -
Outdoor Toy Car
By g_coopster in forum TOY MAKINGReplies: 1Last Post: 14th May 2009, 04:53 PM -
Add your kitchen site for free - Kitchen Directory
By renomart in forum Links to: WEB SITESReplies: 0Last Post: 18th February 2006, 06:30 PM