Picture(s) thanks: 0
Results 16 to 28 of 28
-
16th October 2020, 02:49 AM #16
what am I missing ??
The waste is NOT trapped between the blade and the fence. Trapping the waste is NOT good, but you are not trapping it.
Thoughts on alternatives ...
Could you use the F&F jig to trap the ends of the leg so that the slider could carry the leg past the blade?
a 45 degree sled, as suggested by Riverbuilder and Graeme, so that the blade stays at 90 degrees, but the cut is made at 45 degrees.
use your planner with a tapered sled -- more work than using a scrub plane.
BTW
Don't let BobL see the dust in this photo
nothing wrong with using the scrub planeregards from Alberta, Canada
ian
-
16th October 2020 02:49 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
16th October 2020, 03:41 AM #17
Ian, what you are missing is that the tablesaw pictured is not mine - that is a left tilt. My slider, when converted to a tablesaw using the rip fence, has a right tilt (towards the fence). Mine WILL trap the work piece.
Yep ... scrub plane wins the day.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
16th October 2020, 10:09 AM #18
All this thread and its not your saw pictured? Lol .
Have I missed something ?
I use the largest of these in the inverted router if its a long enough run of legs and worth setting it up . A small number and Id be free hand taking off the corner on the buzzer.
2 Flute - 90deg Vee Groove Bit - Carbide Tipped - Carbitool
Or It may be this one . 2 Flute - 90deg Vee Groove Bit - Carbide Tipped - Carbitool
Both the same for chamfering . Great for London pattern chisel handles if you like them .
On your saw, you could fit a sacrificial wooden fence to your fence and raise your blade at 45 degree through and into it a touch. Then push the tapered legs through with a push stick or two .
-
16th October 2020, 10:54 AM #19
auscab
All this thread and its not your saw pictured? Lol .
Have I missed something ?
Mainly, I have been curious to find a method for a slider that others may use .... which clearly would have eluded my feeble brain. I have other methods to use, which I have done - the easiest being a scrub plane, which was fine to do on 40mm square sections, but this is not as easy with 25 or 30mm sections since these are difficult to grip in a face vise and have clearance to plane. Then a router table makes sense.
Someone here may wonder why I do not simply turn the square sections directly. Well, one can and I have, but with dry Hard Maple there is the risk of an edge splintering and tearing off. Better to first remove the edge.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
16th October 2020, 11:47 AM #20
-
16th October 2020, 12:10 PM #21regards from Alberta, Canada
ian
-
16th October 2020, 03:35 PM #22
Thanks, Ian, saved me posting again.
The workpiece also was not flush against the fence, a bit sloppy; certainly not the way Derek would have sawn it.
Slider Fence 2.jpg
-
18th October 2020, 02:31 AM #23
I shall make up a fixture for the slider after this bunch of stools. There are likely to be many occasions in the future to make use of one.
In the meantime I used the scrub plane ...
Here you can see the corners removed and the round being turned. Dry Hard Maple is not the most fun to turn, although it finishes well.
And enough legs for three stool. All rough turned at this stage.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
18th October 2020, 02:59 AM #24
-
18th October 2020, 03:01 AM #25
Too much "stuff" on the bench, Ian
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
18th October 2020, 11:45 AM #26
-
19th October 2020, 12:23 AM #27
Ian, after a little clean up ...
... I discovered some space at the end of the bench to plane the stretchers ...
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
28th October 2020, 11:31 PM #28Senior Member
- Join Date
- Oct 2010
- Location
- Drouin Vic.
- Posts
- 166
Hi Derek,
I use my SC-2 slider with a wooden frame attached to the slider that I clamp boards or panels onto to make raised panel sections . Easy to setup and use to get good a good finish off the blade and from memory I use about 20 degree blade tilt. Very pleased to hear you are using a Wharton Esherick design as I had the pleasure of a private tour through his house/workshop two years ago in PA USA where many of his special designs are on display.
Cheers,
Paintman
Similar Threads
-
A Ripping Novel
By Robthechisel in forum WOODCARVING AND SCULPTUREReplies: 8Last Post: 10th December 2013, 12:40 PM -
Problems Ripping Mitres/Bevels
By Milo in forum WOODWORK - GENERALReplies: 2Last Post: 23rd March 2010, 12:49 PM -
Out of square bevels on skirting
By philbeez in forum TRITON / GMCReplies: 2Last Post: 10th August 2008, 06:57 PM -
Ripping ply
By Wongo in forum WOODWORK - GENERALReplies: 3Last Post: 31st October 2005, 04:22 PM -
Ripping jig
By Wassy in forum TRITON / GMCReplies: 34Last Post: 6th July 2005, 12:18 AM