Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Scraping.
-
24th July 2011, 11:54 PM #1
Scraping.
The second cabinet was glued up today. While the glued dried I got on with cleaning up the exterior of the first cabinet.
Looking at the finished result, I was struck by the contrast with the, now, rough look of its original state. I think that one of the joys of woodworking comes when the finished state started to emerge, like a flower unfolding.
The second cabinet glued up minus clamps ..
I particularly love it when planing down dovetails and they sharpen in profile and detail. Here I first used a block plane straight across the grain, working one side to the centre, and then the other side to the centre.
I am very concerned about break out at the dovetails, and for this reason prefer to smooth the wood with a cabinet (card) scraper than a smoothing plane. I find there is more control with a cabinet scraper as it is possible to lift the blade just before hitting the dovetail.
The finish off a scraper is not usually as reflective as from a smoother, but I was happy with the finish here (although it is interesting how the camera lens shows up all the flaws in the surface) ...
I was also very happy with the way the dovetails came out. Hardwood to hardwood dovetailing is for masochists. There is no give and no leeway for error.
A few final shots for now.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
24th July 2011 11:54 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
25th July 2011, 11:17 AM #2
Hi Derek,
That is a fair bit of scraping there. Did you have welders gloves on to stop your thumbs from burning?
The grain is looking great.
Cheers
Pops
-
26th July 2011, 02:52 AM #3
Thanks Perry.
Thumbs are holding up
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
26th July 2011, 09:36 AM #4
Makes my thumbs sore just looking at the expanse to be scraped, Derek! Jarrah seems to be one of those woods that responds very well to scraping. They should look very spiffy when done, and sitting in place.
I've done a couple of Jarrah kitchen counter tops, & was well please with the way they came up under a bit (lot!) of scraping. In fact the last time I did a really big area with card scrapers was on some kitchen counter tops (for a large kitchen, too!). After that, I decided life would be a lot better if I bought a LV scraper plane. I find I still have to use the cards to touch-up the really recalcitrant areas, but the plane has been a very welcome addition to the tool kit (or is that a non-addition, since it's part of a set? ).
I could never work out exactly why you get that slightly dull surface off scraper blades. I go to a deal of trouble refining my edges, down to the same grits as for final honing of chisels & plane blades, before turning the burr. Theoretically, they are as sharp as a plane, and certainly produce lovely fine shavings - so why does it look as if the surface fibres are slightly torn? I always meant to take a look at planed & scraped surfaces under a dissecting microscope, to see if that would answer the question, but never got around to it while I had the chance. One of these fine days......
Cheers,IW
-
26th July 2011, 06:38 PM #5I could never work out exactly why you get that slightly dull surface off scraper blades. I go to a deal of trouble refining my edges, down to the same grits as for final honing of chisels & plane blades, before turning the burr. Theoretically, they are as sharp as a plane, and certainly produce lovely fine shavings ...
Different cutting angles. Scraping versus slicing. Type I (lower angle plane) versus Type 2 (scraper) cuts.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
26th July 2011, 09:10 PM #6
Hi Derek. I guess what I should have said is that I've never really grasped the full mechanics of so-called type 1 and type 2 cutting. When I read explanations, I came away feeling a bit like I did after reading some of my more turgid undergrad texts! A cut should be a cut, after all. However, my eyes & tactile senses accept there's a difference, so my logic just says that high-angle cutting (scraping) is not cutting, but something else......
Cheers,IW
Similar Threads
-
The new scraping thread
By Greg Q in forum METALWORK FORUMReplies: 404Last Post: 23rd August 2011, 05:32 PM -
is scraping done in turning?
By mimpi in forum WOODTURNING - GENERALReplies: 13Last Post: 15th July 2011, 02:14 AM -
Scraping practice
By jhovel in forum METALWORK FORUMReplies: 7Last Post: 11th July 2011, 07:01 PM -
Scraping
By wheelie in forum WOODTURNING - GENERALReplies: 8Last Post: 23rd September 2006, 09:40 AM -
Scraping
By 9Fingers in forum WOODWORK - GENERALReplies: 22Last Post: 28th January 2006, 04:32 AM