Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 27
Thread: WIP Rimu Coffee table
-
29th December 2010, 08:10 PM #1Intermediate Member
- Join Date
- Jan 2009
- Location
- Auckland
- Posts
- 48
WIP Rimu Coffee table
Hi everyone
So I have been working on a new piece of furniture over the xmas break. This simple coffee table is for the inlaws.
Its made from recycled Rimu, and is a knock-off of one my mother-n-law was eyeing up a while ago.
The top is made from old barge boards, which certainly take a lot of cleaning up.
Loads of nail holes to fill, and in order to make maximum use of the timber, i am filling the soffit grove on the underside of each board, instead of just trimming the boards down. (Altough I am only filling the last few inches of the groove, which is what can be seen withiout climbing under the table)
Right now im ready to radius the corners of the top, and then profile the edges. But baby is asleep, so I have to find something quiet to do..
I hope to have it assembled and ready for sanding in the next couple of days!
Cheers
Dave
-
29th December 2010 08:10 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
29th December 2010, 08:24 PM #2
-
29th December 2010, 09:23 PM #3
Looking good Sidewz, and a nice bit of recycling, takes some work but very satisfying.
The time we enjoy wasting is not wasted time.
-
30th December 2010, 09:08 AM #4GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
Looking good. You have some nice close grained boards there and the colour should be great
I've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
31st December 2010, 01:19 PM #5Intermediate Member
- Join Date
- Jan 2009
- Location
- Auckland
- Posts
- 48
I have finished plugging all the nail holes, coarse sanding of the top, and i have radiused the corners and applied a profile.
Whoever was putting this particular barge board up must have had some trouble. I had 4 big nails in one spot, and I have ended up completely cutting them out in putting in a wedge.
Came up pretty well, but sadly the colour is slightly off. The surface colour was identical when I cut it, but the wedge sat approx 2 mm high once installed. As I sanded down the 2mm, the colour changed a little bit.
Still, better than 4 big blobs of filler I say .
-
1st January 2011, 07:43 PM #6Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Looking good!! Glad to see the recycling!!
-
1st January 2011, 09:51 PM #7
From a distance is the wedge noticed?
-
1st January 2011, 10:24 PM #8GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
If it is a problem for you , then perhaps you could try your hand at a bit of intarsia over the top of the "patch", perhaps in the shape of a leaf in a contrasting timber.
I've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
2nd January 2011, 07:03 AM #9Intermediate Member
- Join Date
- Jan 2009
- Location
- Auckland
- Posts
- 48
-
2nd January 2011, 07:08 AM #10
Nice bit of recycling.
I don't think you need to apologize for plugs and patches, it's all part of the rich patina.
-
2nd January 2011, 04:03 PM #11Intermediate Member
- Join Date
- Jan 2009
- Location
- Auckland
- Posts
- 48
Thanks for all the comments guys.
yes, recycling timber is very time consuming, but very rewarding. I would estimate that over half the build time is spent recovering timber, straigtening, flattening and plugging nail holes.
Oh, and chaning blades when I dont see a hidden nail
I have finished most of the sanding today, and started assembling the legs.
I need to make a supply run to carbatec, so the final assembly will have to wait a few days (out of long pocket hole screws )
MIght have to pick up a few othertoysessential supplies whilst I'm there.
Cheers
Dave
-
2nd January 2011, 09:44 PM #12
Very good progress.
-
4th January 2011, 07:52 PM #13
Dave
A trick I picked up from a furniture restorer
Spray that area with the plug with some metho - that will let you know how the match will look after you apply finish
I like the use of recycled timber - the table should come up wellregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
4th January 2011, 08:13 PM #14Intermediate Member
- Join Date
- Jan 2009
- Location
- Auckland
- Posts
- 48
Thanks Nick
Yep, thats a good trick, a damp rag also gives a good indication.
The main thing missing here was my patience to get the plug to sit down perfectly snugly.
I always use the offcuts from the end of the boards to cut plugs for that board, ensuring I get a good colour match. However, the plugs need to sit almost flush when installed, as the colour changes through the depth of the timber.
This large wedge plug was a first for me, and I got a bit hasty with it.
All this done, I took it to my in-laws to check the height of the table, and my mother-in-law asked where all the marks and holes were, as she loved the idea of it being made from recycled timber
They have rather high couches, so I made the table a bit taller to start with. The consensus is its too tall, so it's coming home tomorrow for a quick trim, and then some poly.
Cheers
Dave
-
5th January 2011, 08:07 AM #15
Similar Threads
-
Wanting to Buy - 2xTV unit, Coffee Table Dinnng room table
By Overboardkiller in forum WOODWORK - GENERALReplies: 6Last Post: 10th November 2010, 05:59 PM -
re-finishing a RIMU table top
By geoff.l in forum FINISHINGReplies: 1Last Post: 4th May 2010, 10:40 PM -
Tall Coffee Table/Desk/BookCase/Holdall of important bits/Sofa Table
By RufflyRustic in forum WOODWORK PICSReplies: 11Last Post: 3rd December 2009, 12:14 AM -
Rimu Coffee table
By sidewz in forum WOODWORK PICSReplies: 10Last Post: 29th March 2009, 03:31 PM -
NZ Rimu dining table and benches
By TassieKiwi in forum WOODWORK PICSReplies: 8Last Post: 17th February 2007, 03:16 AM