Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 23 of 23
-
28th June 2015, 09:09 PM #16SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
Hi Stephen
what I was alluding to was whether or not the particular insert you are using able to cut the threads per inch you attempted.
I am (almost) confident that inserts have a range of threads per inch they can cut before you need to put a different one in the holder for the next range of threads per inch.
Whether that is 55 deg's or 60 degree's is only a measure of the thread angle and not the amount of threads there is per inch of shank length.
I apologise but I am possibly the worst at explaining things.
Phil
ps after a lifetime of machining and literally hundreds of threads I used an insert to cut a thread maybe 2 months ago. I have only ever used HSS (high speed steel)
-
28th June 2015 09:09 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
28th June 2015, 10:56 PM #17Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Yes, but like most things there are conditions. The main reason offsetting is suggested is to reduce the load on the tool and power requirements as that can lead to chatter and other problems. If you have a rigid set up then this is not such a problem. With smaller machines you can still do it but need to be careful with DOC.
So, with a sharp tool, rigid machine and decent lubrication they are not too problematic. On a Hercus sized machine you may be better off setting the post over for coarse threads although you will probably get away with plunging for finer threads (say 25 tpi or more?)
Michael
-
30th June 2015, 07:05 AM #18Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 920
Thanks Michael,
It's interesting to know that plunge screwcutting can be nicely done.
I think I'll stick to setting over the top slide and cutting from one side though. It works well and with less risk of drama.
Jordan
-
9th July 2015, 07:11 PM #19Novice
- Join Date
- May 2015
- Location
- Newcastle
- Posts
- 23
Hi Phil, the inserts are good for threads fro to 4 TPI,I have given it another go and I'm pleased to say I'm close. Its obvious it's a skill learnt over many years, Imay have been able to pick it up faster in my younger years when I couldremember where my car keys were LOL, but I am still enjoying learning though itseems to take longer these days.
-
11th July 2015, 10:59 AM #20SENIOR MEMBER
- Join Date
- Sep 2011
- Location
- Ballarat
- Age
- 65
- Posts
- 2,659
It sounds like you are winning Stephen and once you get your head around it, it can be surprisingly easy.
What I am liking about old(er) age is walking into the shed to do something and standing there for 10 minutes wondering what the hell it was I was going to do
It's more embarrassing when the missus walks in. Then I normally pick up a piece of steel and take it to the other side of the shed and put it down, grab the previous piece I put there and do the reverse.
She gets bored by this stage and I stand there for another 10 minutes.
Keep giving this screwcutting a crack as it can be very exciting when it works out to be what you were after plus you will save a fortune on dies
If you can private message me your email address I have a couple of good books on the subject in 'Dropbox' that you should be able to access.
Phil
-
11th July 2015, 06:31 PM #21GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
Not sure exactly on the insert that your using but I think you are pushing the boundaries with what you have.
You haven't stated what the tip it is that you are using but I would think larger than an ER16,
you should be looking at an ER11 for your fine thread as this will be better suited, good luck with how they turnout.
-
13th July 2015, 09:01 PM #22Novice
- Join Date
- May 2015
- Location
- Newcastle
- Posts
- 23
-
13th July 2015, 10:28 PM #23GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
You will need a tool to suit the 11 tip, the threading tips are not interchangeable.
Similar Threads
-
Lathe thread cutting change gear calculator
By Vernonv in forum METALWORK FORUMReplies: 57Last Post: 4th December 2012, 12:23 PM -
Thread cutting on the lathe ??
By welder in forum METALWORK FORUMReplies: 126Last Post: 27th October 2012, 02:37 PM -
Thread cutting on the lathe by hand crank
By 19brendan81 in forum METALWORK FORUMReplies: 8Last Post: 10th July 2012, 01:56 PM -
Thread cutting with a lathe stop
By colbra in forum METALWORK FORUMReplies: 15Last Post: 15th April 2012, 01:22 AM -
Hafco AL-336 Metal Lathe Cutting Imp Threads
By steran50 in forum METALWORK FORUMReplies: 17Last Post: 1st September 2009, 10:18 PM