Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Hercus No.0 mill
-
2nd June 2015, 10:53 PM #1Product designer retired
- Join Date
- Nov 2006
- Location
- Heidelberg, Victoria
- Age
- 79
- Posts
- 2,251
Hercus No.0 mill
I'm investigating the plus's and minus's of this mill.
I've spoken to a couple of our esteemed members, and some of their opinions are-
+ small footprint
+ easy to move
- limited head height
- restricted x & y table movement
- can only take light cuts
For those of you that have this little mill, what are your good and bad points?
Did you change the 3 phase motor for a single phase unit, or did you use a VFD?
How does it stack up against the Arboga EM 825?
Ken
-
2nd June 2015 10:53 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd June 2015, 07:51 PM #2Novice
- Join Date
- Jul 2012
- Location
- brisbane
- Posts
- 15
Hi Ken,
I have a late one of these and I love it.
I have the standard 3 phase motor, no VFD, Speed range is great for what i do. I have not done much horizontal milling other than brass but for small vertical work it is great. Super accurate. I have a large mill drill for bigger work but it cant deliver the finish or accuracy of the little hercus. (Both are as new condition)
If you can get one for a good price I doubt you'll be disapointed.
I have a VFD on my lathe and planned to install one on the mill but I doubt I will bother, the speed range is fine on the later machines.
Lyle.
-
3rd June 2015, 09:33 PM #3SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- sydney
- Posts
- 880
Hi Ken,
I like my Hercus. The small foot print and weight make it easy to move. The vertical height can be a problem. I'm running a VFD without any problems.
Ben
-
4th June 2015, 08:32 PM #4Product designer retired
- Join Date
- Nov 2006
- Location
- Heidelberg, Victoria
- Age
- 79
- Posts
- 2,251
Hercus 0 owners?
Surely there are more than two Hercus 0 owners out there.
I'm still seeking opinions about this machine.
There doesn't seem to be much forward/backward movement of the table, longitudinal travel seems ok.
It also seems a very low height machine vice is necessary.
Mal, Allterain50, tells me the serial No. is under the top slide. Is it anywhere else?
I did lift a P/N off the Hercus name plate inside the side door, it was 10L2145. Reckon this is just a Hercus factory No.
Ken
-
6th June 2015, 09:13 AM #5.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
You have been here before Ken - https://www.woodworkforums.com/showth...11#post1316111 And while I have commented off forum, here's a bit more....
When I acquired my No.O I entered another world. I could machine things that I couldn't when restricted to only a lathe with vertical milling slide. Projects became more adventurous, I probably ended up using the mill more than the lathe. You accept that the work envelope is restricted and tailor projects to suit. I made a fair amount of stuff using the mill and probably would have made more had the 13 not appeared.
I imagine few of us could make an Arboga / Hercus comparison. While I have seen Arboga drills I haven't laid eyes on one of their mill drills. The drills I have seen have been of exceptional quality, I'd replace my Waldowns with an Arboga in a flash if I chanced upon something affordable.
If you have an X and Y table combined with a quill and ample Z, why not stick with the Swede?
BT
-
6th June 2015, 07:31 PM #6Product designer retired
- Join Date
- Nov 2006
- Location
- Heidelberg, Victoria
- Age
- 79
- Posts
- 2,251
Hercus 0 mill
G'day BT,
I must be getting old, do you know I don't remember that old post you linked to, sometimes I can't remember where I left the car at the Supermarket or what I did yesterday.
Strange that I can always remember how many bottles of medicine are left in the fridge. At the moment, one.
I have been a Hercus fan dating back to my Tech school days. We had about a dozen 9" imperial models and it was always a fight to get on one. That's where I cut my teeth, at school.
Strangely enough, not one Hercus mill.
So my desire to own a Hercus mill stems from that, plus the fact that it's nice and compact, and I love the look of them. It's a bit like desiring a HP calculator years back.
All my turning and milling work has been done on my Unimat 3 lathe/mill so I'm used to making smallish things.
I still don't have a workshop, insufficient funds, I live with my son, so parts of my house become workshop areas, and a Hercus 0 mill would slip in easily in a corner somewhere.
I like the Arboga, still in storage, but it's about twice the size I can deal with.
Bob, thanks for your input on and off the forum.
Ken
-
7th June 2015, 10:41 AM #7GOLD MEMBER
- Join Date
- Mar 2011
- Location
- Dural NSW
- Age
- 82
- Posts
- 1,120
Hercus O Mill
Ken
Agree with Bob.
The Hercus O Mill I own is 3 phase.
Purchased it 2nd hand about 20 or so years ago.
Done plenty of work with it, a good solid little mill.
Hand scraped the X & Y slides a little while back,& peened the bronze nuts to tighten up a slight wear & backlash.
Its now as good or better than new
The main limitation is the head room or Z movement, but it has done everything, I have needed to accomplish.
A moveable quill as in Bobs 13 would be an advantage.
Purchased a Hercus Dividing Head for it, & will use that from time to time.
The no 3c Collets I use on my Hercus 260 lathe are also excellent on the Mill.
regards
Bruce
ps Like yourself, I have always been a Hercus fan. They make quality stuff.
Similar Threads
-
Hercus OLM Mill
By lyleman in forum THE HERCUS AREAReplies: 2Last Post: 7th March 2015, 06:43 PM -
Hercus O Mill
By bwal74 in forum THE HERCUS AREAReplies: 10Last Post: 6th January 2013, 03:52 PM -
Hercus Mill
By wheelinround in forum THE HERCUS AREAReplies: 2Last Post: 7th July 2012, 11:35 AM -
Arboga EM825 mill vs Hercus model 0 mill?
By neksmerj in forum METALWORK FORUMReplies: 23Last Post: 14th May 2011, 03:16 PM -
Hercus Mill
By PBrown in forum METALWORK FORUMReplies: 5Last Post: 6th May 2009, 01:04 AM