Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
Thread: Hercus capstan lathe
-
13th May 2015, 09:53 PM #1Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Hercus capstan lathe
As some of you may have read on the main forum, I was thinking about getting a small lathe for second operations and a member offered me his Hercus capstan parts with the rack slide and a bed. The bed is not branded Hercus or Southbend so I assume it is a Sheraton - apparently the profile was all the same.
Among the many problems I still have to sort out is a headstock of some sort, but more immediately the bed is too long (around 1m) for the space available. Does anyone know whether Hercus ever made a short bed version of their 9"? The other options are to cut down the existing (Sheraton) bed although that has risk as I don't know how much it will move, or to make up a suitable section - considering that I will only be using this for parts up to say 3" long as that is close to the travel of the capstan and that the capstan and slide don't move along the bed when the lathe is in action, a short section of bed would not need the fit or accuracy of a "normal" lathe.
Pics of the bits -
(the blue tinge is grease)
P1020979 (Medium).JPG P1020980 (Medium).JPG
(And if anyone has a desire for a 1m long Sheraton bed please let me know - it is likely to have some wear (I haven't checked out it) but could be better than the one you have)
Michael
-
13th May 2015 09:53 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th May 2015, 07:44 PM #2.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Michael,
My apology for the tardy response. I have a fair amount of Hercus literature and I have never seen any reference to or suggestion of a shorter 9" bed than the standard 40". South Bend however did make short beds, short as 24" but I image they are real thin on the ground even in the US of A.
If the bed did distort as a result of a few or several inches being lopped off, would it matter much if you are only using the capstan's travel? Who knows, the bed is webbed and maybe distortion would be minimal at worse??
BT
-
21st May 2015, 07:49 AM #3Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
Most people seem to think the same thing Bob. While I don't mind getting stuck into broken or dysfunctional equipment, I do hesitate to do irreversible things to "good" parts - hence asking about alternatives first.
Michael
Similar Threads
-
Drill press capstan
By malthemender in forum GENERAL & SMALL MACHINERYReplies: 2Last Post: 5th May 2012, 06:48 PM -
An "unearthed" CVA precision capstan lathe
By jhovel in forum METALWORK FORUMReplies: 14Last Post: 2nd July 2011, 12:16 PM -
DB Fletcher Capstan Ilona expanding table
By MiLKey in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 2Last Post: 14th September 2010, 01:47 PM -
simpson capstan winch in austraila?
By weisyboy in forum SMALL TIMBER MILLINGReplies: 43Last Post: 4th August 2009, 08:50 AM -
Ward 3DS Capstan Lathe Manual ??
By Plushy in forum METALWORK FORUMReplies: 4Last Post: 25th March 2009, 03:56 AM