Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 1 of 1
-
15th September 2023, 12:10 PM #1Most Valued Member
- Join Date
- Aug 2015
- Posts
- 4,434
Hercus Milling Slide Modifications
A couple of modifications to make the slide more convenient to use on those rare occasions that it gets used.
The graduated collar on my vertical slide would bind when the feed screw was turned clockwise so I modified it allowing the collar to rotate freely no matter which way the handle was turned.
Attachment 403711 Attachment 403712 Attachment 403713
The above photos show the original assembly.
IMG_20190911_120326916.jpg IMG_20190911_124533573.jpg IMG_20190911_112153655.jpg
The modifications consisted of boring out the graduated collar to accommodate a taper pinned collar and grooving the feed screw to facilitate the installation of a circlip.
IMG_20190911_132125515.jpg
IMG_20190911_133111456.jpg IMG_20190911_133252918.jpg IMG_20190911_135229747.jpg
For convenience I replaced the collar lock screw with knurled thumb screw.
IMG_20210626_151944637.jpg
Then I made a lever to lock the slide. I had made a couple of levers for locking my two compound slides so while I had the Turnado and the mill set up I took the opportunity to make an additional lever for the milling slide.
IMG_20210619_143452954.jpg IMG_20210619_170112469.jpg IMG_20210619_170031499.jpg IMG_20210620_142052717.jpg IMG_20210623_173443334.jpg IMG_20210626_135617192.jpg
IMG_20210626_144923359.jpg
BT
Attached Images
- IMG_20190911_120326916.jpg (109.7 KB)
- IMG_20190911_124533573.jpg (109.9 KB)
- IMG_20190911_112153655.jpg (81.1 KB)
- IMG_20190911_132125515.jpg (91.0 KB)
- IMG_20190911_133111456.jpg (57.5 KB)
- IMG_20190911_133252918.jpg (53.7 KB)
- IMG_20190911_135229747.jpg (131.1 KB)
- IMG_20210626_151944637.jpg (105.8 KB)
- IMG_20210619_143452954.jpg (59.6 KB)
- IMG_20210619_170112469.jpg (158.1 KB)
- IMG_20210619_170031499.jpg (117.5 KB)
- IMG_20210620_142052717.jpg (103.3 KB)
- IMG_20210623_173443334.jpg (107.4 KB)
- IMG_20210626_135617192.jpg (95.5 KB)
- IMG_20210626_144923359.jpg (73.2 KB)
Read the full thread at metalworkforums.com...
-
15th September 2023 12:10 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Posts
- Many
Similar Threads
-
Hercus 9C cross slide milling rig.
By MWF FEED in forum THE HERCUS AREAReplies: 0Last Post: 26th March 2019, 01:40 PM -
Hercus 9C cross slide milling rig.
By MWF FEED in forum THE HERCUS AREAReplies: 0Last Post: 26th March 2019, 01:30 PM -
Milling Slide for Lathe
By MWF FEED in forum METALWORK FORUMReplies: 0Last Post: 25th March 2019, 03:30 PM -
Cross Slide Scraping Hercus 260
By Abratool in forum THE HERCUS AREAReplies: 3Last Post: 14th November 2014, 05:06 PM -
Vertical Milling Slide - An Alternative
By Anorak Bob in forum THE HERCUS AREAReplies: 4Last Post: 1st November 2011, 10:15 AM