Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
-
5th July 2011, 08:02 PM #1Rodddd
- Join Date
- Aug 2008
- Location
- Melbourne
- Posts
- 48
Hercus Vertical Milling Attachment
Hi Guys,
I have got a couple of castings from Swarfmaker for a vertical milling attachment for the Hercus lathe.
I am wondering if someone (or more that one!) can pop some photos of the attachment in this thread so I can come to grips with the end product All the photos I have seen are of the table only, with little detail of the back / handle.
If I can be cheeky and ask for photos of the side, back, and disassembled would be greatly appreciated.
Thanks in Advance.
Rodd.
-
5th July 2011 08:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th July 2011, 06:23 PM #2.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Here's a start Rodd.
If no one else pipes up I can provide more photos tonight.
BT
-
6th July 2011, 11:59 PM #3.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Some photos and some very rough drawings of the attachment. I have included photos of the vise and indexer in case someone is interested.
-
7th July 2011, 11:32 AM #4.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Rodd, Is this what you are after?
BT
-
7th July 2011, 02:29 PM #5Rodddd
- Join Date
- Aug 2008
- Location
- Melbourne
- Posts
- 48
Bob - You Are A Marvel!!!
Hi Bob,
Thanks for the photos they are brilliant - exactly what I was looking for
The sketches are an added bonus!!!
Thanks Again for Your Efforts
This may be a slow thread (based on the trillion other things I have on at the moment!) so stay tuned
Rodd
-
30th October 2011, 06:07 PM #64-6-4
- Join Date
- Mar 2009
- Location
- Melbourne
- Posts
- 295
Vertical Attachment
dear Rod one thing you should be aware of with the vertical milling attachment. As you can see in the first photo in this thread is the position of the attachment is in the hole for the top slide. The disadvantage here is that when you wind the attachment across to t5he center line you have lost most of your sideways movement.
A way out of this is to have an extended cross slide as shown. and you have to make a spacer that goes beneath the attachment so that it can be bolted to the tee slots shown. An additional 4 holes should be drilled and taped around the original hole for the attachment. These holes should be same center distance as the tee slots. This enables you to move the vertical head to any position on the cross slide so you do not run out of traverse. Hope this is of help. This is not my Idea it was published in the Model Engineer by a bloke called Lofquist. This was one of the first mention I saw of an extended crosslide. I was in the casting game and made quite a few of the extended crosslides. Yours 4-6-4
-
30th October 2011, 06:22 PM #7Member
- Join Date
- Jan 2010
- Location
- Perth
- Posts
- 84
Hi Rodd, Andy Lofquist available Metal Lathe. Good site, knowledgeable, thorough bloke.
All the best with the slide, Mark
-
31st October 2011, 06:15 PM #8.
- Join Date
- Nov 2008
- Location
- Perth WA
- Age
- 71
- Posts
- 5,650
Myford's method.
I will second 4-6-4's comments. With the vertical slide mounted on the cross slide you are limited in the amount of usable travel available.
https://www.woodworkforums.com/f189/v...native-129971/
Myford's milling slide is attached via tee slots allowing more flexibility in positioning. Whilst I made a tee "nut" to fit my compound slide I never got aound to making some nuts to allow the fitting of the Myford slide to the extended table. I have a couple of milling machines so the lathe is seldom used for milling. There are times though that the lathe can facilitate milling setups too awkward for either mill.
Regards from Lyon
BT
-
31st October 2011, 08:53 PM #94-6-4
- Join Date
- Mar 2009
- Location
- Melbourne
- Posts
- 295
Vertical slide
Yes Bob I have always had the view that dual purposed for machines never quite works. I have always had lathes and mills. But having said that cost can be a powerful opponet when it comes to machines.
-
1st November 2011, 09:33 AM #10Rodddd
- Join Date
- Aug 2008
- Location
- Melbourne
- Posts
- 48
Hi Guys,
Thanks 4-6-4 good idea. I was originally going to use Andy's castings for the slide and changed my mind when Swarfmaker offered his as an alternative.
Like the idea of the mount - May need to pop it on the Christmas list
My garage is 'full' of Metal Lathe castings - need to stop collecting and start making!!! Everything that I have heard about the castings is that they are brilliant to work with. Andy's drawings are clear and comprehensive.
Last year I was in the US and had the opportunity to chat to Andy (for about an hour) - he is a great bloke; full of knowledge and more than willing to share it. I would recommend any of his kits to anyone!
Rodd.
Similar Threads
-
Vertical Milling Slide - An Alternative
By Anorak Bob in forum THE HERCUS AREAReplies: 4Last Post: 1st November 2011, 10:15 AM -
Vertical Milling Machine for routing?
By tbkmagic in forum MUSICAL INSTRUMENTSReplies: 14Last Post: 23rd September 2009, 08:08 PM -
Does anyone know anything about the 'GB Vertical Mill' attachment that sells on eBay?
By Brendan1152 in forum SMALL TIMBER MILLINGReplies: 2Last Post: 14th October 2008, 11:42 PM