Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: tasmanian Myrtle.
-
2nd December 2007, 05:09 PM #1Senior Member
- Join Date
- Feb 2004
- Location
- Perth,WA
- Posts
- 246
tasmanian Myrtle.
Hi,
I've put a question in the "timber' section that might perhaps be best here - would a piece of Tasmanian myrtle, 39mm thick, cut well (easily) - not too difficult? with a scrollsaw.
Thanks,
Bob H.
-
2nd December 2007 05:09 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd December 2007, 07:36 PM #2
-
2nd December 2007, 11:43 PM #3
Bob, that is getting just a little too thick for my way of thinking.
It also depends on the tightness of the curves and so forth. Can the scrollsaw you use cope with timber this thick? If it can, and that timber is hard, take your time, and cut slowly, allowing the blade to cool off every now and then, by backing off and letting it run without cutting for a few seconds.
Turn the saw off, take a break, then go back at it another time. I can't say I have cut that timber, and therefore I can't comment, only guide you into cutting thick and hard wood.
At that thickness, you will have little clearance between the top surface and the arm, so take care your knuckles don't get a tap or four.Buzza.
"All those who believe in psycho kinesis . . . raise my hand".
-
3rd December 2007, 01:51 PM #4Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
It's pretty fine grained stuff usually; Bootle lists the density as 700kg per cube. About the same as Euro. Beech.
Cheers, Ern
-
5th December 2007, 05:21 PM #5
You could cut it.... but I'd not say easy.... you'd have to have one of the very good saws for starters. At that thickness it's too easy to push the blade sideways making for a distorted cut.... if you were to make a puzzle chances are the pieces would get stuck, unless you are very experienced and patient.
I wouldn't do it on my Delta.. not for something intricate anyway... way too thick.
Juvy
-
5th December 2007, 05:27 PM #6
The first question is how intricate is the pattern,.
Next does the finish of the blade matter.
Are you able to sand easily after the cut.
On material this thick you would want a 10 tpi or less blade which gives you a rough finish.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
26th December 2007, 09:34 PM #7Senior Member
- Join Date
- Feb 2004
- Location
- Perth,WA
- Posts
- 246
Bit late acknowledging but thanks for the replies. It was for a try at that three dimensional cutting - a simple clock insert. Turned out decently (he says modestly)
Thanks,
Bob H.
-
26th December 2007, 09:42 PM #8
How about giving a bit detail on how it went? Problems? How you solved them..... and how about a photo?
JuvyWoodcrafters Haven
Wodonga - Supplies for Turners and Woodcrafters
Mobile 0407261703
-
28th December 2007, 10:01 PM #9Senior Member
- Join Date
- Feb 2004
- Location
- Perth,WA
- Posts
- 246
Picture attached (if I can work it out?). It is approx 200mm high, used a No. 5 skiptooth, no problems, and finished with Rustins Danish Oil. I cut on a WMS. My only wish is that I could get clock inserts that require a hole quite a bit smaller than the surround, this one required a hole only some 2mm smaller in diameter than the clock surround, not much room for error.
Bob H.
-
29th December 2007, 09:06 AM #10
That came out really nice, Bob
Guess there is a difference cutting things with good saws .....
one day I might not have a choice... might have to get one.... heard that Deltas aren't send to Australia anymore....... bummer....
JuvyWoodcrafters Haven
Wodonga - Supplies for Turners and Woodcrafters
Mobile 0407261703
-
29th December 2007, 03:33 PM #11
all you wannabee delta saw owners need to write to Black & Decker Australia and complain
-
29th December 2007, 06:26 PM #12
You might have a good idea there!
I have my Delta, but am already wondering what'll be next.
I'm happy with it and would hate to have to change....shoot I don't even like using someone else's Delta... got mine set just the way I like ... like driving someone else's car.... or worse.... someone driving mine and changing the seat , mirror etc....
JuvyWoodcrafters Haven
Wodonga - Supplies for Turners and Woodcrafters
Mobile 0407261703
Similar Threads
-
Looking for Tasmanian Myrtle veneer
By BrettC in forum MARQUETRY and INTARSIAReplies: 10Last Post: 20th August 2007, 10:12 PM -
Cabinet for CD player in Tasmanian myrtle
By Rocker in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 16Last Post: 20th November 2004, 08:16 PM -
Tasmanian myrtle speakers
By tktran in forum WOODWORK PICSReplies: 9Last Post: 14th March 2004, 10:56 PM -
Tasmanian Pink Myrtle
By raltenhofen in forum WOODTURNING - GENERALReplies: 14Last Post: 9th October 2003, 02:29 AM -
Tasmanian Figured Myrtle table
By WoodWad in forum WOODWORK PICSReplies: 4Last Post: 17th July 2003, 02:15 PM