Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: what glue?
-
30th December 2005, 11:18 PM #1
what glue?
I am trying to get my head round gluing the wood that I want to turn to a piece of wood that is fixed to my face plate, BUT what is the best?? glue to use for this, what do you boys use????and will I need to put paper between the two woods??? or glue wood to wood????..
You see I find it hard to believe that it will not fly off as soon as I put a chisel upto the work????
-
30th December 2005 11:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
31st December 2005, 12:07 AM #2
Can't help you with turning because I don't have a lathe to know anything about it, however PVA glues are stronger than the wood is.
For hardwoods I am a fan of Yellow Glue. I use Titebond II for most things. Others here know more than me and will tell you about it soon enough I am sure. Try doing a search it might have been covered in the past.
StudleyAussie Hardwood Number One
-
31st December 2005, 12:24 AM #3
You would be surprised how little it takes to hold things on a faceplate. For small articles, I have even had lots of success with thin double-sided tape (carpet-tape) - very quick and easy. Hot-melt glue works too and you can micro-wave it when you're finished to allow separation. PVA is safest of course but separation is usually achieved by parting the work-piece off when finished. Bonding strength required is usually determined by the size and balance of the piece you want to attach. If it sails across the workshop - find stonger bonding method!!!
-
31st December 2005, 02:54 PM #4Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Yep, I've used hot melt (good quality mind) when finishing the foot on an irregular piece. Five small blobs on a good size lump of Jarrah. (Thanks TTIT for the m/w tip; I just knocked my carrier off which was a bit risky).
And yes, it depends on what you're trying to do.
Paper and glue is ideal for spindle turning when eg. you're going to split a piece to make two decorative halves.
If it's faceplate turning, again, depends on your application. You know about bringing up the tail stock for extra support? And/or finishing off the inside of a foot off the lathe?Cheers, Ern
-
31st December 2005, 03:29 PM #5
For cheese-platters and the like, where the blank's only a short length of the bed and screw-mounting is not an option, I'll use the paper/PVA method.
However, I screw a larger circle of ply to the faceplate, at least 2/3 of the blank diameter and glue to that. I always bring up the tailstock until it has to be removed, occasionally I'll mount a jacob's chuck with a long dowel in lieu of the normal tailstock bearing to give me better access.. Better safe than sorry.
Seperation's just a matter of using a good knife-edge and a few taps of a hammer. I'm a tad wary of hot-melt, having had seperation problems in the past.
A microwave, eh Ern? That sounds like it has possibilities. Any particular method? I'd be finding out for myself, 'cept the shed's still set on "roast." Bloody weather.
- Andy Mc
-
31st December 2005, 06:06 PM #6Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Hi SkewChi,
Yep, bit hot. I insulated my workshop and put in a big box a/c ... dirt cheap these days and I like to keep the Yallourn folk in work.
The microwave tip btw was TTiP's.
Generally for finishing the bottom of platters and the like I use Cole jaws or a homemade vacuum chuck. Neither have the regular or powerful grip of your techniques so I guess I don't have your patience either, despite the a/c.
Anyway, have a good one tonight and best wishes for the new year. Looking forward to reading more of your posts.Cheers, Ern
-
4th January 2006, 11:03 PM #7Intermediate Member
- Join Date
- Dec 2004
- Location
- Truro, NS, Canada
- Posts
- 46
Typically, for finish turning bowls up to 16", I just use a regular hot glue gun to put a layer of hot glue on a glue block and finsih the bowl. I have a friend that uses it for bowls up to three feet. After that I can not say.
Similar Threads
-
Are Your Glue Joints Repairable?
By Bob Smalser in forum GLUEReplies: 8Last Post: 16th December 2005, 10:45 AM -
Gluing wood for turning
By R12chard in forum WOODTURNING - GENERALReplies: 3Last Post: 10th April 2005, 05:51 AM -
What glue should I use?
By chook in forum GLUEReplies: 3Last Post: 12th November 2004, 07:51 PM -
Glue help
By Different in forum GLUEReplies: 9Last Post: 28th September 2004, 04:14 PM -
Hide Glue Q & A
By ubeaut in forum GLUEReplies: 1Last Post: 12th November 1999, 03:01 AM