Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
11th April 2002, 12:48 PM #1
Need help removing glue pigment from hands
Hi all,
I've just finished glueing up the second lutiens garden bench. I've used the outddoor polyurithane (?) from carbi-tec.
Its the one that bubbles up and changes color to yellow. What a mess.
Anyway I had to glue 60 joints in an hour (befor it hardened).
Anyway I got it all over my hands and can't seem to get it off.
Any suggestions as to how to remove the pigment without removing the skin?
------------------
Thanks,
Barry G. Sumpter
Proud Tritoneer
[This message has been edited by barrysumpter (edited 11 April 2002).]Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
11th April 2002 12:48 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th April 2002, 03:00 PM #2SENIOR MEMBER
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 455
What? No Triton products to help you out here? :0 (sorry Barry had to do it).
Not sure about the Glue/staining, maybe add a day or two and it will start wearing off, or track down some thinners?
Stephen
-
11th April 2002, 04:00 PM #3
Acetone (may have no effect once cured ?), followed by gentle washing with warm soapy water for 5-15 minutes.
Otherwise a couple of days should see it peel - unless you develop a rash - in that case see a doc.
Wear gloves next time & good luck with the new job.
-
11th April 2002, 04:45 PM #4
Thanks Gents,
Rang the Manufacturers (duh :b)
Absolutely nothing will remove it.
It just has to wear off.
Now, how do I explain to my new employer and co-workers why I don't have enough personal hygene to wash my filthy hands.
Finally got a break with employment, but still humbled by everyday mishapps.
------------------
Thanks,
Barry G. Sumpter
Proud TritoneerThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
11th April 2002, 07:52 PM #5Member
- Join Date
- Jan 2001
- Location
- Australia
- Posts
- 55
Pumas Stone and teeth gritted, maybe a scotch or two before.
Harry
Tasmania
-
11th April 2002, 08:05 PM #6
Yeah, Harry,
The Scotch sounds good.
Drunk enuf an oo cars bout me filty hans? ay?
hic!
baz
------------------
Thanks,
Barry G. Sumpter
Proud TritoneerThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
12th April 2002, 02:44 PM #7
Barry,
My wife is one of the unusual women, who that when they see something new, buys it. She found what is fine emery or wet & dry paper, glued on a plastic paddle which you use in a bath or shower(when skin has softened) for removing hard skin/callouses from the feet. Works well on the feet.
I was gluing up a large number of brass tubes into pen blanks using a type of superglue and found at the end of it all, I had somewhat black hands and fingers. Nothing seemed to remove it. I was in the shower and saw the paddle sitting above the shower door and you guessed it, I tried it and it worked.
A couple of points though
1/ make sure hands are well softened by the water
2/ don't rub too hard, it will remove more than the outer layer of skin.
KevKev
-
12th April 2002, 11:42 PM #8
Thanks for that Kev,
End of day three and I really went to town scratching them off in a really hot shower. Almost all gone, just bits and pieces left when the show ran cold.
I'll ask my lady about the emory board.
------------------
Thanks,
Barry G. Sumpter
Proud TritoneerThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
16th April 2002, 04:08 PM #9
we used to have a similar problem with a glue for polystyrene great stuff but the only thing to get it of was 120 grit sand paper coarser is too painfull finer does little.
gloves are a wonderfull thing i keep 2 boxes of disposable gloves in the workshop 1 latex ( cheap ANSEL from the supermarket ) & 1 of a better plastic food grade glove. great for painting & staining and othe messy jobs. when you are finnished just peel em off into the bin. great.
Cheap disposables don't stsnd solvents much at all though.
I am still looking for a good solvent proof glove for serious stuff like playing in thinners, cleaning spray gunns & the like. I have been told nitrile is the go.Any thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.