Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Patching with CA glue
-
18th May 2008, 04:33 AM #1Novice
- Join Date
- May 2008
- Location
- Hawaii
- Posts
- 15
Patching with CA glue
Ok veteran turners, I need your input. I'm doing a hollow form and the piece I'm working on has a natural hole thru the center ( the holes will be on the sides). Can I use the CA, coffee grinds or wood from the piece to make the holes seem smaller and natural. Can anyone give me their technique?
-
18th May 2008 04:33 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
18th May 2008, 09:19 AM #2Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
How big are the holes?
Twopack epoxy may be better , depending on hole size.
-
18th May 2008, 11:16 AM #3
Dribble a little CA... Dribble a little coffee... Dribble a little CA... Dribble a little sawdust/shavings... Repeat. Leave rough til thoroughly cured. then sand. The depressions left by roughness will look like an inclusion.
Like Artme says... depends on the size of the hole.Al
Some minds are like concrete thoroughly mixed up and permanently set.
-
18th May 2008, 03:09 PM #4
Yep, what they said. If you can stick your thumb in you maybe outa luck.
Could try some bark, carefully shaped to fit then CA and coffee grinds.
I have some success with this, but it depends on how you fit the bark etc. Go as natural a look as you can get.
all the bestInspiration exists, but it has to find you working. — Pablo Picasso
-
18th May 2008, 04:34 PM #5Banned
- Join Date
- Jun 2007
- Location
- Otautahi , Te Wa'hi Pounamu ( The Mainland) , NZ
- Age
- 69
- Posts
- 2,114
Kiaora Keoni ,
how would gluing tightly fitting twigs into the holes go ?
When tidied up they may look like knots ,
designer knots
na Jock
-
18th May 2008, 04:50 PM #6Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
We have a saying in Oz: 'mutton dressed up as lamb'.
Sometimes leaving it as mutton will in the end look best, ie. go rustic.
But if they're small holes ... good advice above.
Post a pic.
Added: with too many holes in my deep hollowing practice piece, and fair-sized ones at that which have structural rather than aesthetic implications, I'm having good results with 5 minute Araldite mixed 1:1 with ground coffee. Have yet to hollow out and see how well it holds thoughCheers, Ern
-
19th May 2008, 12:40 AM #7GOLD MEMBER
- Join Date
- Jan 2007
- Location
- Adelaide
- Posts
- 2,794
I've been told that 5 minute epoxy is less robust than the slow setting one, but can't see why it should fail, given that it is certainly stronger than the wood. The only problem I can think of could be that if it is a fairly large filled area in a very thin wall of soft wood the difference in resistance to the tool could tend to push the plug out of the wood. Does it make sense? Just hypothetically, I have no experience of it.
So far, never had any problem with any size fill of epoxy/coffee.
-
19th May 2008, 08:10 AM #8Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Yes, the std 'overnight' epoxy is stronger.
Cheers, Ern
-
19th May 2008, 05:36 PM #9Yes, the std 'overnight' epoxy is stronger.Inspiration exists, but it has to find you working. — Pablo Picasso
-
19th May 2008, 06:04 PM #10Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Erk ... I may regret not knowing that ;-}
Cheers, Ern
Similar Threads
-
patching two-pac
By spartan in forum FINISHINGReplies: 13Last Post: 15th December 2005, 09:00 AM