Needs Pictures: 0
Results 1 to 6 of 6
Thread: Adaptor sleeve stuck in collet
-
22nd December 2022, 12:22 AM #1Intermediate Member
- Join Date
- Jul 2022
- Location
- Gympie, QLD
- Posts
- 35
Adaptor sleeve stuck in collet
Total router noob.
Bought a second-hand Ryobi router with 1/2" collet. It had a 1/4" adaptor sleeve.
Went to change the bit... compu'er says no
20221220_162743.jpg
After much, much wrestling, I was able to get the bit out, but the sleeve refused to come with it.
It's completely stuck in there. I've tried to fish it out, scratching it like a champ in the process (obviously I'll have to get a new one).
Any help on how to get it outta there would be greatly appreciated coz it's absolutely making me crazy -- like, or or or even
-
22nd December 2022 12:22 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
22nd December 2022, 02:05 PM #2
Looks to me like the collet was inserted too far (Should be flush) and the outer bits of the threaded outer have 'closed in' slightly over it. Doesn't take much to make life miserable.
I'd try a small timber wedge (of hard wood!) in the slot(s) on the outer thread first to try and remove pressure first. I strongly recommend against prying with screwdrivera or similar although I have been known to resort to just that.
If that fails, I'd get a small dome-headed screw (perhaps a knob bolt for drawers, ground down a tad?) that will fit down thru the collet and try to hook the head underneath. Perhaps squeeze a short length or two of nail, wood or similar alongside to reduce the chance of the bolt slipping out of position, but nothing wedged tightly in there.
Fit the collar back on, then slip a large washer(s) over the end of the bolt and snug up a nut. Then locking the shaft and undoing the collar would act like a puller. You don't need to pull it all the way out, just enough that you can get a pair of pliers or vice-grips or whatever onto the end and finish removal.
I've used a few variations to this method, but they all depend on just what odds 'n sods I have lying around, ready to hand.
- Andy Mc
-
22nd December 2022, 02:14 PM #3
The same method to remove bearings --> Wet newspaper, paper towel or heavy grease.
Put pieces down and with a nicely fitting shaft of some kind, tap it down. repeat. The collect will hydraulic itself out.
watch this from 5'00" (Yanks talk too much)
-
22nd December 2022, 03:41 PM #4
-
22nd December 2022, 10:04 PM #5
This even works for bearings etc with slightly damp bread, or anything that can be made to flow under pressure, however sluggishly, but the mandrel uses to apply the pressure needs to be a neat fit in the item being removed, able to be inserted to pressurize, and be removed to refill for the next pressure cycle.
Looking at the distortion of the spindle bore, the unit will either not properly grip bits allowing them to move in use, or alternatively have runout, vibrate, and not run true, two tight gaps in the slots and one broader one.I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
31st December 2022, 06:21 PM #6
No chance that is going to work on the collet. The liquid will just escape out the slots in the collet as soon as you hit the plunger and no pressure will be generated.
Similar Threads
-
Help! My Triton collet is stuck, and it's not the typical stuck collet!
By old750 in forum TRITON / GMCReplies: 1Last Post: 1st November 2009, 10:03 PM -
Router Collet Sleeve
By Sir Stinkalot in forum ROUTING FORUMReplies: 14Last Post: 25th April 2008, 10:55 PM -
Stuck Collet
By gilbo in forum ROUTING FORUMReplies: 6Last Post: 6th April 2008, 05:23 PM -
Help Stuck router collet nut
By pjmoran in forum ROUTING FORUMReplies: 7Last Post: 20th June 2003, 09:25 PM