Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Cast router table.
-
14th November 2021, 09:11 AM #1Senior Member
- Join Date
- Jul 2019
- Location
- Box Hill
- Age
- 66
- Posts
- 186
Cast router table.
Hi, wondering if anyone has looked at options for various cast router tables and router lift kits. I know there are a few cast iron systems on the market.
So in a nut shell.
1. which cast iron top.
2. router lift kit.
3. fence system.
4. which router.
-
14th November 2021 09:11 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th November 2021, 08:35 PM #2GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 1,134
I have a cast iron router table.
Not sure if it is really worth it. Mine is a cheap one from carbatec, the milling/grinding on it is below average, so it seems to rust quicker, But i have it mounted on the end of my sawstop table saw.
I think its easier to get a proper router lift mounted into a timber/plastic coated router top.
-
15th November 2021, 06:50 AM #3Senior Member
- Join Date
- Jul 2019
- Location
- Box Hill
- Age
- 66
- Posts
- 186
Ok and thanks for the reply..
-
30th November 2021, 08:01 AM #4Member
- Join Date
- Apr 2021
- Location
- New Zealand
- Age
- 74
- Posts
- 56
We used the Kreg Precision Router table with a TRA001 for several years at the Blenheim Menz Shed. Then about two years ago we were donated several machines including a router table with cast iron top and a rather clunky tenon jig. I believe it was an early Carbatec system. It came with the MOF001 so I swapped out the routers and we kept the cast iron table. I've never seen anyone use the tenon jig but it also has a turn screw fence adjustment that is nice to use. When I have used it I have more than once found it made black marks on the work piece, and it would definitely make a white rag soaked with degreaser go black. All in all, I wish we'd kept the Kreg table.
As for routers and lifts I would chose the Triton TRA001 every time as it does not need a lift, and it has a lot of power. I used a Bosch 1600E with its fixed base in my own router table, and while it does have above table adjustment it is even more clunky than the tenon jig I mentioned. It is OK lowering the router, but if I want to raise it I have to reach under the table and give it a helping hand. So I bought a TRA001 and will have that permanently mounted in my table, and keep the Bosch for use with its plunge base. It's horses for courses. I absolutely love the Bosch router with its plunge base, but the TRA001 is a much better table mounted router.
Cast iron tables should be a good bet for routers. I mean our table saws never seem to mark the workpiece, and cast iron is going to stay flatter than wood.
-
1st December 2021, 11:31 AM #5Senior Member
- Join Date
- Jul 2019
- Location
- Box Hill
- Age
- 66
- Posts
- 186
Thanks for the replies Trevor.
-
1st December 2021, 01:05 PM #6GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
My Men's Shed purchased the Timbecon unit with all the bells and whistles, it is very good and a real pleasure to use and easily use accurately.
https://www.timbecon.com.au/sherwood...l-router-table
We also purchased their in-house router for the table. It also works very well. We did have the first unit self destruct, this was immediately replaced by Timbecon. I believe it was a case of dust ingress into a sensor, something that hasn't been an issue at all with the replacement unit.
https://www.timbecon.com.au/sherwood...y-router-motor
With the router placed inside the box and the supplied hose to the tabletop, dust, shavings or whatever are minimal. In fact I used the Shed router yesterday along with another member who had never used this machine before; he remarked that not only was it great to use, but the dust not sucked up was minimal to the point of needing to look for the dust to clean-up.
You may wish to just get the table and use your own stuff, which is fine. I would though, suggest you look at the micro adjusters. These can be seen on the fence edge. Find the two locking knobs on the LH side of the fence in the pictures, in-between the two knobs there is a knurled wheel, this is the micro adjuster. The lower back knob locks the fence, loosening the higher front knob enables you to finely adjust the fence with the knurled wheel; one then simply locks the front knob and you are ready to go with your new setting.
https://www.timbecon.com.au/sherwood...adjustment-kit
The complete unit is reasonably heavy, so unless you are really pushing it around, it should not move. The top on ours is flat.
Mick.
-
3rd December 2021, 06:45 AM #7Senior Member
- Join Date
- Jul 2019
- Location
- Box Hill
- Age
- 66
- Posts
- 186
Hi Mick and thankyou for replying. I think I will have to go and have a look see.
I'm in the middle of trying to buy a spindle moulder from WA as well....and get this the cost of transport from WA to Vic in nearly 1/3 ie $1000 the price of the Cast iron Router set up.
Steven
-
2nd July 2022, 12:22 PM #8Novice
- Join Date
- Jul 2022
- Location
- Southern Calif
- Age
- 74
- Posts
- 10
Harbor Freight
Too bad HF is not in Australia, I bought a cast iron router table top form them 20years ago, it was very reasonable. The first one was warped so bad 1/4" out of flat, they sent another one works great with a discontinued Freud router.
Similar Threads
-
WEST AUST Cast iron router table top and Sherwood router lift
By bueller in forum WOODWORK - Tools & MachineryReplies: 11Last Post: 15th March 2020, 05:02 PM -
Triton Router table RTA300 VS Carba-Tec Cast Iron Top Router Table
By pellcorp in forum TRITON / GMCReplies: 17Last Post: 30th April 2009, 02:43 PM -
Cast iron router table
By wilco in forum HAND TOOLS - POWEREDReplies: 5Last Post: 16th July 2006, 07:40 PM