Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
11th June 2007, 09:34 PM #1newbie that's keen
- Join Date
- Mar 2007
- Location
- Bonny Hills, NSW
- Age
- 64
- Posts
- 517
height adjuster for table mounted router
When I was looking at mounting my router in a table (I have a Ryobi table saw combination which has a place to mount my router) I looked at all the do it yourself height adjusters for table routers and thought 'this is all too hard'. So I did what I thought was simpler and built a little table and mounted an old car jack on it. Probably lots of people have done this before but I didn't see it anywhere so wanted to share my idea. I just use the jack handle to adjust and I should be able to get precise adjustments althought I haven't worked out how many mm adjustment is a quarter turn.
I'd be interested in other simple ways of doing this and what others have done as adjusting by hand is awful. This of course covers all types of routers. I also hand routed a small impression of the car jack base into the table to make it a bit more sturdy.
Mick
-
11th June 2007 09:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
11th June 2007, 10:15 PM #2SENIOR MEMBER
- Join Date
- Apr 2006
- Location
- Melbourne Victoria
- Posts
- 621
Mick, I have seen similar methods with car jacks. There is no constant relation between the cahnge in height per turn. When closed it takes a lot of turns to open a little and when fully opened one tunr makes a huge differnece. (It probably is an equation relating to the sine/cosine of the angles, Trigonometry at school wasn't a complete waste after all)
Have you removed the spring from the router, it makes lifting easier. Dont forget to still lock the router once you reach the required height, it eliminates the lttle amount of play.
Pretty flash table as well for the use
-
12th June 2007, 01:18 PM #3newbie that's keen
- Join Date
- Mar 2007
- Location
- Bonny Hills, NSW
- Age
- 64
- Posts
- 517
Thanks for the tips.
I should have worked out that the height adjustment will NOT be equal due to how a car jack works.
The table (my first 'without help' project) was made from pine from an old bed. It was the good strong timber I had available.
I might have a look at the springs but remember seeing other threads where taking them out was a pain.
I'll remember about locking - I probably would not even have thought about it until I had had my share of problems!
cheers
Mick
-
12th June 2007, 01:25 PM #4
Simple but good
-
12th June 2007, 08:58 PM #5
Your are probably better off leaving the spring in to provide resistance, after all it no effort to raise the router anyway. Good idea.
David L
One of the great crowd beyond the bloom of youth on the Sunshine Coast
-
12th June 2007, 10:18 PM #61/16"
- Join Date
- Mar 2007
- Location
- Adelaide South Australia
- Posts
- 544
I just love simple things that work.
The ingenuity of forum members never ceases to amaze me.Don't force it, use a bigger hammer.
Timber is what you use. Wood is what you burn.
-
13th June 2007, 11:23 AM #7GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
G'day Mick and welcome aboard I have posted this a long time ago but it still works well and may just give you some other thoughts.
http://www.woodworkforums.ubeaut.com...ad.php?t=23893
Regards,
Bob
-
13th June 2007, 01:29 PM #8newbie that's keen
- Join Date
- Mar 2007
- Location
- Bonny Hills, NSW
- Age
- 64
- Posts
- 517
thanks for all the feedback. If nothing else, it is encouraging. Also, the link to a previous thread using a car jack will make me search more thoroughly next time. There are definitely some things to think about, especially the pressure (and potential blocking) on the air vents.
Mick
Similar Threads
-
Challenge to Create the Ideal Router Table
By rodm in forum ROUTING FORUMReplies: 215Last Post: 26th July 2021, 08:34 PM -
Router plate and insert ring height fixed
By Intheshed in forum TRITON / GMCReplies: 2Last Post: 25th May 2004, 10:08 PM -
Extending the height of table mounted drill press
By barrysumpter in forum WOODWORK - GENERALReplies: 10Last Post: 16th December 2003, 09:05 PM -
Over head Router over head height winding for Triton router table?
By Maxi in forum TRITON / GMCReplies: 5Last Post: 5th November 2002, 09:09 AM -
Blade Height Winder Review
By Noel Butcher in forum TRITON / GMCReplies: 6Last Post: 13th May 2000, 02:31 PM