Thread: Notch Weatherboard- Best method

Are you wanting to put that particular V shape into your Weatherboard?
If you were to stack your boards on the angle required, it should be a simple matter then of running your router along a straight edge. You may need to put offcuts from your boards in between, so that they are all the same angle. Depending on how many boards you need to do, the jig could be fairly simple, or elaborate.
HTH
Kryn

Originally Posted by KBs PensNmore

Are you wanting to put that particular V shape into your Weatherboard?
If you were to stack your boards on the angle required, it should be a simple matter then of running your router along a straight edge. You may need to put offcuts from your boards in between, so that they are all the same angle. Depending on how many boards you need to do, the jig could be fairly simple, or elaborate.
HTH
Kryn

Hi Kryn, thanks for the reply.

My photo isn’t the clearest, but the notch doesn’t go all the way through. So if you looked at the board from the back it would look like a standard board. Or have I misunderstood your method?

This might sound completely bonkers, so forgive me if so.

But looking at the notch you want to cut, it strikes me that a corner chisel will cut this easily. You make up a jig to hold the chisel at the correct angle, and also provide a stop position for the board, thus ensuring all your notches start at the same height on the board, and are a consistent angle.

Placement can be done by measuring and marking the board.

If this is confusing (it's hard to describe in text), let me know, I will sketch up a picture of what I mean.

Router, in a jig, carbitool make a v cutter with a sharp point . Easy.

Hi, These notches were originally hand cut with a saw. On a reno I did years ago, I made a hardwood guide block & cut them with a tenon saw. Tedious, but effective. Peter

Thanks for everyone's replies.

I went the router and jig option. I could have increased the angle of the jig slightly to make a 'shorter' notch but I'm pretty happy with how they turned out. Here's a few pics for reference if anyone ever wants to do the same.


94223878_689431011860119_7673700853810724864_n (1).jpg

91500046_671521833595006_7913708926300848128_n.jpg


91561929_302986107342045_4541183748011458560_n.jpg


91593159_1646951092112920_2022103047139753984_n.jpg


91709971_231578338228321_2263008346887946240_n.jpg


93802317_628885084626316_8653994166658793472_n.jpg


94302368_226807751922371_2243906565738332160_n.jpg


93987975_666643364155498_1908821180173778944_n.jpg


94325481_161436411909926_4947398580886306816_n.jpg

Nice but that first picture of the domino teetering on the edge of the bench gave me chills. Someone kicks the lead or steps on it and you’ll be crying to the tune of $2000. Put your tools on the deck.

Well done!! I have not seen the bell cast look before, impressive.

Originally Posted by riverbuilder

Nice but that first picture of the domino teetering on the edge of the bench gave me chills. Someone kicks the lead or steps on it and you’ll be crying to the tune of $2000. Put your tools on the deck.

I thought you told me they were throw-away and not worth the money?

Originally Posted by riverbuilder

Nice but that first picture of the domino teetering on the edge of the bench gave me chills. Someone kicks the lead or steps on it and you’ll be crying to the tune of $2000. Put your tools on the deck.

Ha, fair point. If it was like that it means I was using it only seconds before and was just about to use it again. It normally goes on the ground when not in continued use.

Originally Posted by Repete

Well done!! I have not seen the bell cast look before, impressive.

Thanks! I'm going for an overall arts and crafts look and I thought the flare might detract from that but I think I like it. You see them on a few Queenslander's from the 20's and I'm pretty sure that was the last time one was built in Brisbane so thought I'd set myself the challenge.

It was VERY time consuming. Every angle was different on two planes and because I'm thinking of keeping them as raw timber (arts and crafts) the joins had to be pretty spot on. It's also not the driest of timber so hopefully there's not too much movement. I used a single piece for the entire row so that if it did shrink it would be fairly uniform.

I've still got another one to go on the level above.