Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
-
3rd November 2014, 09:40 AM #1SENIOR MEMBER
- Join Date
- May 2013
- Location
- Somerset Region, Qld, AU.
- Age
- 66
- Posts
- 602
How Do I Route a 188mm Diameter Hole ?
Clock Overview.jpgGreetings,
I'm in the middle of making a clock as a Christmas gift for a family member, and have run into a bit of a challenge with safely making part of the clock face's structure. The clock is loosely based on a plan that was published in Woodsmith magazine (Issue 89) back in 1993 (see photo at right).
Inner Door.jpg
The operation that is proving to be a bit of a challenge is making the hole in the centre of the clock face panel (it's labelled "Inner Door" in the drawing at left). The panel is 3/4" thick Silky Oak. So, time to find an appropriate method of making that 200mm hole.
The original magazine article says to use a Jig Saw to cut the hole out, and then clean it up with a rasp. So I grabbed a scrap of hoop pine and gave it a go. Maybe it's my jig saw technique (or lack of it), but the resulting hole was very rough. And the jigsaw blade kept bending sideways, so the hole is quite oversized in some places on the underside. I also did a test with a fret saw, and that was quite successful, but my little fret saw doesn't have a big enough throat to be able to cut that hole, and I don't fancy buying a bigger fret saw or coping saw just to do one job.
So, I've started considering different ways of using a circle cutting jig and a router, either hand-held or mounted in the router table, to cut this hole. I normally prefer to use the router table as I tend to feel that most operations are a bit safer on a router table, rather than hand holding the router. But I'm not sure that is the case this time. As it's a hole I'm cutting, it'll need to be a plunge cut.
So, the question is .......
What is the best and safest way to cut this hole.....?
- Use a circle cutting jig and a hand-held router, and plunge cut.
- OR, rig up a circle cutting jig on the router table. Using this approach would entail dropping the workpiece onto the spinning router bit to start the plunge cut. (That's the specific bit that doesn't seem real safe to me !)
- OR, some other approach entirely. Could I do the job more safely using a template ?
- A local Woodie last night raised what he thinks is an issue in relation to using a router to cut a large hole like this. He is concerned that parts of the circle will be a climb cut when using the router - is climb cutting an issue in this case ?
Your suggestions & ideas please .... Including ideas for suitable single use circle/hole cutting jigs ?
Regards,
RoyManufacturer of the Finest Quality Off-Cuts.
-
3rd November 2014 09:40 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd November 2014, 03:45 PM #2GOLD MEMBER
- Join Date
- Oct 2007
- Location
- vic clayton
- Posts
- 1,042
I use a jigsaw(festool)with a circle cutter attachment. After marking out two circles one a blade width inside the diameter of the finished size I first drill a hole large enough for the blade then I use a small file to square the hole to the diameter of the cutting circle and then I cut out the circle.
it works quite well,
I then sand to the line using a spindle sander.Some people are like slinkies - not really good for anything, but they
bring a smile to your face when pushed down the stairs .
-
3rd November 2014, 06:36 PM #3
One of the methods I'd use would be using the router hand-held with a trammel bar (or circle cutting jig) on a thin piece of ply or similar to make a template.
Then clamp the template to the face and use a bearing bit to clean up the hole cut by the fret-saw. Or, if you've tossed that and are starting afresh, drill a hole in the waste area of the face (ie. inside the template) with a spade-bit to start the bit cutting in, thus avoiding the need for any plunge cut at all. This will also let you avoid the need for any climbing cuts as well!
- Andy Mc
Similar Threads
-
Which Route should I go with my Kitchen Cabinets?
By Jcari in forum WOODWORK - GENERALReplies: 3Last Post: 21st March 2010, 10:58 PM -
how to route tenons
By DPPATT in forum ROUTING FORUMReplies: 5Last Post: 4th November 2008, 05:29 PM -
vintage stanley route
By fubar in forum ROUTING FORUMReplies: 0Last Post: 20th October 2008, 09:16 PM -
going the triton route - advice pls
By old_picker in forum TRITON / GMCReplies: 3Last Post: 5th March 2006, 07:52 PM -
What tool to use to route granite?
By nik in forum HAND TOOLS - POWEREDReplies: 16Last Post: 24th June 2004, 04:53 PM