Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Source of 5 degree router bits
-
6th October 2012, 05:19 PM #1Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
Source of 5 degree router bits
Hi all, as the title says, I am after some 5 deg router bits to use to make some patterns for metal casting. My router has 1/4 inch shank and the bit can have a flat on the bottom.
The draft angle is not critical but something around 5 deg would be best, any ideas appreciated. I have looked through the usual places, best I can come up with is to use a tapered endmill, though maybe not the best for cutting timber (which is milky pine by the way).
Cheers.
Russell.
-
6th October 2012 05:19 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th October 2012, 06:26 PM #2
I've always found Carb-i-tool a good source of weird router bits....
Had a quick look through their cattledog, and the nearest I could find is this thing with 7 degree bevel (see attached). Any use?
-
6th October 2012, 06:30 PM #3
By the way, if you actually want to purchase carbitool bits, I've found these people to be very good
laminate trim - combination flush 7 degree bevel trimming
It is possible to buy direct from Carbitool, but they always seem rather surprised when you ring up and try to order stuff.
-
6th October 2012, 07:54 PM #4Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
Hi Mr brush, I may have to go that way, unfortunately the actual taper section is quite small, so it would need multiple passes to achieve any decent depth, I was hoping to find something like a bevel bit with around 20-25 mm of actual taper.
I can get around the shallow depth in software but if I can do it without getting involved in too much maths life would be a lot easier, lol.
Cheers.
Russell.
-
6th October 2012, 07:58 PM #5Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
Something like this may be the go...quite a bit pricey but at the end of the day I am only cutting milky pine so it should last forever, unless I run it into a clamp that is...
3 Flute M42 Cobalt Centercutting Tapered Single End Mills - Tapered End Mills | MSCDirect.com
-
7th October 2012, 11:15 AM #6Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
Just in case anybody else follows this thread, I have ordered this :
McJING Tools Online
From what I can work out the taper should be about 7 degrees.
Not exactly what I was after but beggars can't be choosers.
I would have liked to be able to rough out with the same cutter but this way I can rough out with a straight cutter then use the taper to give the final tapered contour.
Cheers.
Russell.
-
7th October 2012, 03:31 PM #7Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Carbitool also will make bits to order, might be worth asking for a quote.
-
7th October 2012, 07:45 PM #8Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
That is not a bad idea, if I start doing a lot of this type of work I will check it out.
Cheers.
Russsell.
-
13th October 2012, 11:10 PM #9Senior Member
- Join Date
- Nov 2008
- Location
- Far North Queensland
- Posts
- 330
Well first test run of the tapered bit today and it works a treat ! I won't be casting this weekend but the pattern looks the part
The part is a spindle holder for my next router.
Cheers.
Russell.
Similar Threads
-
FESTOOL query #6 – Router Bits and OF 2200 Router Table
By FenceFurniture in forum FESTOOL FORUMReplies: 2Last Post: 12th February 2011, 07:37 AM -
campbell hausfeld 34 degree framing nailer and 30 degree nails
By oggie in forum HAND TOOLS - POWEREDReplies: 0Last Post: 14th September 2009, 11:51 AM -
FYI- source for custom made bits
By HonkyLips in forum WOODWORK - GENERALReplies: 0Last Post: 22nd July 2004, 10:59 AM -
Melb retail source for Carb-i-tool router bits ?
By Justin in forum HAND TOOLS - POWEREDReplies: 6Last Post: 2nd February 2004, 08:07 PM