Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
15th January 2016, 02:12 PM #1Intermediate Member
- Join Date
- Jan 2016
- Location
- British Columbia, Canada.
- Age
- 67
- Posts
- 37
General International Dust Collector
IMG_0076.jpgIMG_0024.jpgIMG_0025.jpg
I purchased a cyclone type dust extractor, and ran 4 - 4" outlets for my tools. My 10" jointer and my 20" planer both have a 6" outlet which I reduced to 4" with no plugging issues at all. The machine is a little loud but I always wear hearing protection anyway. Its a little awkward removing the 55 gal. drum when its full from underneath but thats not a big deal, it works great.
-
15th January 2016 02:12 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
15th January 2016, 02:31 PM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,790
Its a shame you did all that ducting in 4".
That Extractor already has an 8" inlet and outlet so it would appear to be capable of at least 1200 cfm.
Irrespective of the Extractor used, Using 4" ducting immediately throttles the flow to ~400 CFM which is a factor of 2.5 less than what is required for fine dust control.
To get the full 1200 cfm of flow the ducting has to be 6" as do the ports on the machinery.
One other thing I notice is you appear to have the blast gates at machine level rather than at the trunk entry level.
This can lead to sawdust from one machine dropping down the drop down ducting to the other machines so you may wish to regularly clear any dust that does this. If one machine is not used for some time this can choke the drop down to the point where the extractor cannot clear that duct.
It's always better to have the gates close to the trunk line.
I wear ear protection often but would not like to have to wear it for every single operation that required dust extraction.
Here in Oz we don't usually have heating issues so we are able to put our extractors outside which gets rid of the noise and any fine dust that escapes the filter or ducting.
However, some folks cannot do that so they enclose the duct extractor inside a sound proof enclosure inside their shed and vent the exit air outside their shed.
If you want to retain the heat you would have to vent back inside the shed but can at least reduce the extractor noise this way.
-
15th January 2016, 04:40 PM #3
I agree with bob about the 6" ducting. Can't believe how much difference that makes, even with my little 2hp dusty. Would be worth upgrading at some stage. With that cyclone it might suck the paint right off the machine, but it will certainly grab the dust.
6" ducting certainly adds to the cost of the ducting though. Each junction is easily 5 times more expensive than 4".
Nice workshop though. Looks super organised and practical. Needs a bit more mess to make it believable though...😄
TravSome days we are the flies; some days we are the windscreen
-
15th January 2016, 05:25 PM #4GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 2,743
What Trav wrote - much too clean.
Similar Threads
-
All in one workbench / dust separator / dust collector
By HeadScratcher in forum DUST EXTRACTIONReplies: 15Last Post: 9th July 2012, 12:25 AM -
Homemade Cyclonic Dust Collector to replace a Triton Dust Bucket
By crowie in forum DUST EXTRACTIONReplies: 3Last Post: 7th May 2012, 08:34 AM -
General International Chuck
By Paul39 in forum WOODTURNING - GENERALReplies: 9Last Post: 26th October 2010, 04:42 AM -
help with dust collector DCA 300
By macklin in forum TRITON / GMCReplies: 21Last Post: 18th August 2008, 06:19 PM